answersLogoWhite

0

An input device. It is because it let the source to flow.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

What is the purpose of a resistor applied to the base of a transistor?

Any system you design will have an input and an output. The output will connect to the input of another system which will load it, so when you are designing any system you have to consider how loading it will effect the circuit performance.


What is the difference between switch and limit switch?

rectifier diodes handle larger amounts of power. A switching diode handles much less amperage but at a quicker rate. There are switching diodes that can switch power on and off in several nano-seconds.


What is the input and output voltage range of ic7408?

A: The answer deviate from IC to ic . It is defined not as voltage but rather as unit loads. In other words there is a limit to how many inputs can be tied together along with how many units can be driven for reliable operation. So basically is a question of current sink and source for both input and output which strictly relates to reliable triggering voltage levels. If I remember i used the 8 for unit load for the input and 40 unit load for the output. These numbers are general use for design.


How a combinational clipper works?

A combinational clipper is a type of electronic circuit used to limit or "clip" the amplitude of an input signal. It typically consists of diodes and resistors arranged in a specific configuration. Here's a basic explanation of how a combinational clipper works: **Input Signal**: The input signal is the waveform that you want to clip. It could be a sine wave, square wave, or any other waveform. **Diodes**: The key components in a clipper circuit are diodes. Diodes allow current to flow in only one direction. In a combinational clipper, diodes are arranged in such a way that they conduct when the input signal exceeds a certain voltage level (called the clipping level). **Clipping Level**: The clipping level is the voltage level at which the diodes start conducting. It determines the maximum (positive or negative) amplitude of the output signal. **Resistors**: Resistors are used to limit the current flow through the diodes and to set the clipping level. They are connected in series with the diodes and the input signal. **Output Signal**: The output signal is obtained across the diodes. When the input signal exceeds the clipping level, the diodes start conducting, effectively "clipping" the signal. This means that any portion of the input signal above (or below, depending on the configuration) the clipping level is removed, resulting in a clipped output waveform. **Configuration**: The configuration of the diodes and resistors determines the clipping characteristics of the circuit. For example, in a simple clipper circuit, one diode may be connected in series with the input signal in a forward bias configuration, causing it to clip the positive portion of the waveform. Similarly, another diode may be connected in series in a reverse bias configuration to clip the negative portion of the waveform. Overall, a combinational clipper works by selectively conducting current through diodes to limit the amplitude of the input signal, resulting in a clipped output waveform.


Where you use damping resistor?

Damping Resistor on Inputs/Outputs (R)Series damping resistors (SDR), denoted by R in the device number, are included at all input/output and output ports of designated devices (see Figure below). The SDRs limit the current, thereby reducing signal undershoot and overshoot noise. Additionally, SDRs make line termination easier, which improves signal quality by reducing ringing and line reflections.This tutorial is based on the Understanding and Interpreting Standard Logic Data Sheets application report (SZZA036).

Related Questions

What does a plc does?

Programming Logic Controller is a controller, which gets input from sensors,read/limit switch and controls the output according to the Ladder logic program.


What is the function of a limit switch on a furnace?

A limit switch on a furnace is a safety device that monitors the temperature inside the furnace. If the temperature gets too high, the limit switch will shut off the furnace to prevent overheating and potential damage.


What is the purpose of a limit switch in a furnace?

A limit switch in a furnace is a safety device that shuts off the furnace if it gets too hot, preventing overheating and potential damage or fire.


What is the purpose of a resistor applied to the base of a transistor?

Any system you design will have an input and an output. The output will connect to the input of another system which will load it, so when you are designing any system you have to consider how loading it will effect the circuit performance.


Where is the limit switch located on a furnace?

The limit switch on a furnace is typically located near the heat exchanger or burner chamber. It is a safety device that monitors the temperature inside the furnace and shuts off the burner if it gets too hot.


What is the function and importance of a furnace limit switch in a heating system?

The furnace limit switch is a safety device that monitors the temperature inside the furnace. It is important because it helps prevent the furnace from overheating, which can lead to damage or even a fire. When the temperature reaches a certain level, the limit switch shuts off the furnace to protect it and the surrounding area.


What is the difference between switch and limit switch?

rectifier diodes handle larger amounts of power. A switching diode handles much less amperage but at a quicker rate. There are switching diodes that can switch power on and off in several nano-seconds.


How does limit switch work using plc?

A "Programmable Logic Controller" can have a switch to either tell the machine when it has reached a certain position at or near the limit of its travel, or a switch that over-rides the maximum or minimum programmed limits for safety. The mechanics can be electrical, laser, pneumatic, or any type that is reliable for the device.


What is the input and output voltage range of ic7408?

A: The answer deviate from IC to ic . It is defined not as voltage but rather as unit loads. In other words there is a limit to how many inputs can be tied together along with how many units can be driven for reliable operation. So basically is a question of current sink and source for both input and output which strictly relates to reliable triggering voltage levels. If I remember i used the 8 for unit load for the input and 40 unit load for the output. These numbers are general use for design.


What is the purpose of a limit switch on a furnace and how does it contribute to the safe operation of the heating system?

A limit switch on a furnace is a safety device that monitors the temperature inside the furnace. If the temperature exceeds a safe level, the limit switch shuts off the furnace to prevent overheating and potential hazards like fires. This helps ensure the safe operation of the heating system by preventing dangerous situations caused by excessive heat.


What does the limit switch do on a furnace and how does it contribute to the overall functionality of the heating system?

The limit switch on a furnace is a safety device that monitors the temperature inside the furnace. If the temperature gets too high, the limit switch will shut off the furnace to prevent overheating and potential damage. This helps ensure the safe and efficient operation of the heating system by preventing dangerous situations and maintaining proper temperature control.


How can I test the limit switch on a furnace?

To test the limit switch on a furnace, you can use a multimeter to check for continuity. First, turn off the power to the furnace. Then, remove the wires connected to the limit switch and set your multimeter to the continuity setting. Touch the probes to the terminals on the limit switch. If the multimeter beeps or shows a reading of zero ohms, the limit switch is functioning properly. If there is no continuity, the limit switch may need to be replaced.