answersLogoWhite

0

There can be no answer for this without knowing how strong a resistor is involved. (Ohms)

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Engineering

A circuit has 25 ohm light bulb and t 120 volts what is the current?

I = E/R = 120/25 = 4.8 amperes


A 2000 watt heater connected to a 120 volt circuit will draw a current of?

Current (amps)=Watts/Volts =2000/120 =16.75 =16.75 amps


What is the amperage in an electric circuit when the voltage 120 volts and the resistance is 40 ohms?

Ohm's Law states Voltage = Current x Resistance. You rewrite the equation as Current = Volts / Resistance to solve for current.


What is the electrical voltage from the house outlet to the power supply?

The average voltage a house outlet will give actually depends on how far of a distance the house is from a transformer on the pole. If the house is fairly close to the transformer, it will probably give around 120 volts. However, if the house is a bit far from the transformer, it will probably give around 107 volts.


What is a 208 circuit?

The 208 volt configuration is one phase of a three phase source at 240 volts, where the 208 volt circuit is connected between the center tap of one 240 volt phase (usually a grounded neutral, in the style of a standard 120/240 split phase system) and the high delta connection on either of the other two phases. 208 circuit would consist of two phases of a 208 volt wye system or could be all three phases. The voltage between conductors would be 208 volts. The voltage to ground from any phase would be 120 volts. A 240 volt delta system would give you a high leg to ground, somewhere around 190 volts and the other two would be 120 volts to ground.

Related Questions

What is the typical number of amps per circuit and what is the typical number of volts that enter your home and what is the typical number of volts for each circuit and what is a gfi?

The typical number of amps per circuit is 15 or 20. The typical number of volts that enter a home is 120/240 volts. The typical number of volts for each circuit is 120 volts. A GFCI (Ground Fault Circuit Interrupter) is a safety device that helps prevent electric shock by quickly disconnecting power when it detects a ground fault.


How much power flows through a circuit with 1 amp and 120 volts?

The power flowing through the circuit can be calculated using the formula P = I * V, where P is power, I is current, and V is voltage. In this case, P = 1 amp * 120 volts = 120 watts. Therefore, 120 watts of power flows through the circuit.


What is the curren in an ac circuit with 120 volts and a 60 watt light bulb?

You want to know how many amps in that circuit. To do so, divide the Watts by the Volts. in your case it would be 60 watts / 120 volts = 0.5 Amps.


A circuit has 25 ohm light bulb and t 120 volts what is the current?

I = E/R = 120/25 = 4.8 amperes


Is there a converter for 220 from 120 amps?

This question makes no sense unless you mean volts instead of amps. And no, not for residential. Your panel feeds 120 volts or 240 volts depending on the way things are hooked up. You can wire circuit that is currently connected 120 as 240, however unless it is a dedicated circuit, YOU WILL BLOW UP YOUR APPLIANCES. Consult a qualified electrician.


What is 50 percent of 120 volts?

50% of 120 volts = 50% * 120 = 0.5 * 120 = 60 volts


How do you make a light circuit flash?

Wire in a turn signal flasher in series with the circuit you wish to flash. The flasher has two terminals. Just insert the flasher anywhere in the circuit. It will make/break the circuit to make the lights flash. This is considering that the circuit is 12 volts and not 120 volts.


What type of motor is the inducer motor?

A circuit board is the inducer motor. It runs off of 120 volts.


Can you plug 120 volts into an 85 watt cigarette lighter in a car?

An automobile cigarette lighter uses 12 Volts DC. A typical 120 Volt circuit would destroy the 12 volt lighter.


Can you wire a 120 volt ballast to a 347 volt circuit?

No, you cannot wire a 120 volt ballast to a 347 volt circuit. The ballast is designed to operate at a specific voltage, in this case 120 volts, and connecting it to a higher voltage circuit like 347 volts can damage the ballast and pose a safety hazard. It is important to match the voltage rating of the ballast to the circuit it will be connected to.


What percentage is 150 volts 0f 120 volts?

150 volts is 125% of 120 volts.


Is a branch voltage in each branch of a parallel circuit less than the applied voltage?

Yes. In a 240 volt circuit, the total applied voltage is 240 volts but each leg is carrying only 120 volts.