answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

What is the third terminal on electric equipment?

The third terminal connects to earth ground.


How do you wire up a dayton 1 horse power electric motor with compacitor?

To wire a Dayton 1 horsepower electric motor with a capacitor, first ensure the power is off and the motor is disconnected from the electrical supply. Identify the capacitor terminals and the motor's wiring diagram, typically found on the motor's nameplate. Connect the capacitor's positive terminal to the motor's start winding and the negative terminal to the common terminal; then connect the run winding to the common terminal as well. Finally, connect the power supply leads to the appropriate terminals, ensuring all connections are secure and insulated before turning the power back on.


Electric motor parts?

Electric motor parts are pieces of electric motors. Some examples of electric motor parts are: bearings, carbon brushes, gasket materials, pumps, soft starters, and terminal boxes.


How do you connect a targa capacitor to your amplifier?

To connect a Targa capacitor to your amplifier, first ensure the amplifier is turned off and disconnected from power. Connect the positive terminal of the capacitor to the positive power terminal of the amplifier, and the negative terminal of the capacitor to the negative power terminal. Finally, connect the capacitor's ground terminal to a solid ground point on the vehicle. Always double-check your connections and polarity before powering the system back on.


What can you do to fix a circuit which is burned out in a load center?

If the circuit has not damaged the bus bars in the distribution panel just change the breaker out for a new one. If the wire insulation has burned you might want to think about changing the wire for a new one. Wire burn back is caused by loose terminal connections at the breaker. As a general maintenance procedure shut off the main breaker and go over all of the breaker terminal connections to make sure that they are tight.

Related Questions

What you need to make a circuit?

To establish an electric current, there are two requirements that must be met. There must be a closed conducting path that goes from the positive terminal to the negative terminal. The second requirement is to have an electric circuit for the energy to move a positive test charge against the electric field.


How does electric current in a electric cell passes?

From the Positive terminal (+ve) to the negative terminal (-ve).


What direction will an electric current flow?

from positive terminal to negative terminal


What does 'terminal' mean?

A point of connection for closing an electric circuit is known as terminal.


What is the third terminal on electric equipment?

The third terminal connects to earth ground.


How should I connect the red wire to the light switch?

To connect the red wire to the light switch, you should attach it to the terminal marked as the "load" or "hot" terminal on the switch. Make sure to turn off the power before making any connections to avoid the risk of electric shock.


How do you connect a bulb holder to a battery source?

To connect a bulb holder to a battery source, first, ensure the power is off for safety. Connect one terminal of the battery to one terminal of the bulb holder using insulated wires. Then, connect the other terminal of the bulb holder to the remaining terminal of the battery. Ensure all connections are secure to allow the electric current to flow and light the bulb.


Where do electric current move?

Electric current moves through wires or conductive materials in a closed loop circuit, from the positive terminal of the power source to the negative terminal. Electrons carry the negative charge and flow from the negative terminal to the positive terminal.


When removing the battery leads from the terminals you do what first?

Disconnect the negative - terminal first, then the positive + terminal. Unfasten the battery hold down clamp. When reinstalling the terminal connections connect the positive terminal first.


Can you touch a battery terminal safely?

No, it is not safe to touch a battery terminal as it can cause electric shock or burns.


What are the wiring connections for a starter relay on a 1993 Ford truck?

Battery to a large terminal Starter to other large terminal Trigger wire to small terminal (if you have an extra small terminal on new relay disregard)


Are in excess at the negative terminal of an electric cell?

In an electric cell, there are excess electrons at the negative terminal. This accumulation of electrons creates a negative charge, which leads to a potential difference between the negative and positive terminals. When a circuit is completed, the electrons flow from the negative terminal to the positive terminal, providing electric current. This movement of electrons is what powers electrical devices connected to the cell.