answersLogoWhite

0

The cold start-up procedure for a turbine typically involves several key steps. First, the system is inspected to ensure all components are in good condition and any necessary maintenance is performed. Next, the lubrication system is activated to ensure proper oil circulation before ignition. Finally, the turbine is gradually brought up to operating speed while monitoring parameters such as temperature and pressure to ensure safe and efficient operation.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Continue Learning about Engineering

What procedure of turbine commissioning?

the steam strikes/enters the turbine th turbine rotats at requried speed.then it connected to genaretor ,the electricity genareted


What do you mean by turbine synchronization?

During a typical power plant startup, all components of the power plant are started slowly. The turbine is first rolled at a slow rpm. Then the rpm is increased gradually to a point where it can match the frequency of the grid. At this point, the turbine can be synchronized with the grid and start outputting electricity into the grid.


What is warm rolling of steam turbine?

You don't start a large turbine cold. Typically, the lubrication system is started, the turning gear is engaged and warming steam (a small amount of steam, not enough to turn the turbine) is admitted to the turbine to warm and initially expand the shaft and casing. If this isn't done, thermal shock from the admission of high pressure superheated steam into the cold turbine could damage it.


What is turbine barring system?

A turbine barring system is a mechanism used to rotate a gas or steam turbine slowly when it is not in operation. This slow rotation helps to evenly distribute temperature and prevent thermal stresses, thereby extending the life of the turbine components. The system typically engages the turbine shaft through a barring drive, allowing for maintenance and inspections while ensuring that the turbine remains in optimal condition. It is crucial for preparing turbines for startup and for maintaining their health during extended outages.


What is cranking in a gas turbine?

Cranking in a gas turbine refers to the process of initiating the engine's startup sequence by rotating the turbine's shafts using an external power source, typically an electric motor or a dedicated starting system. This action allows the gas turbine to reach the required speed for fuel ignition and combustion. Cranking is essential for overcoming inertia and ensuring smooth acceleration to operational speeds before the turbine takes over and self-sustains its operation.

Related Questions

How many type of turbine cold startup?

water tube boiler


What is cold rolling of steam turbine?

When Turbine shaft temp is below 100 deg.centigrade,Then rolling of turbine carried out it is called cold rolling.


What is the startup time for wind?

The startup time for wind turbines typically ranges from a few seconds to several minutes, depending on the turbine design and wind conditions. Once the wind speed reaches the turbine's cut-in speed (usually around 3-4 meters per second), the turbine can begin generating electricity. However, achieving full operational capacity may take longer as the turbine gradually accelerates to its rated speed. Overall, the startup process is relatively quick compared to other forms of energy generation.


What procedure of turbine commissioning?

the steam strikes/enters the turbine th turbine rotats at requried speed.then it connected to genaretor ,the electricity genareted


What are the turbine generator start up rmp for a cold start?

It may be depends on the Constructor/ Design of Turbine .


What steps needs for start a steam turbine from cold conditon?

steam turbine cold start up list:


What do you mean by turbine synchronization?

During a typical power plant startup, all components of the power plant are started slowly. The turbine is first rolled at a slow rpm. Then the rpm is increased gradually to a point where it can match the frequency of the grid. At this point, the turbine can be synchronized with the grid and start outputting electricity into the grid.


What is cold rolling wider?

When turbine shaft temp is below 100 deg.centi, then rolling of turbine carried out it is called coldrolling wider.


Procedure of a small wooden wind turbine electrical energy from wind?

i dont know what it is either


What is warm rolling of steam turbine?

You don't start a large turbine cold. Typically, the lubrication system is started, the turning gear is engaged and warming steam (a small amount of steam, not enough to turn the turbine) is admitted to the turbine to warm and initially expand the shaft and casing. If this isn't done, thermal shock from the admission of high pressure superheated steam into the cold turbine could damage it.


Is it ok to have a colonoscopy with a head cold?

It is usually best to wait until you are well for any procedure. Inform the doctor who is scheduling your procedure of the cold and they can decide, based on your symptoms and the date of the procedure, if you should have the procedure rescheduled.


What is cranking in a gas turbine?

Cranking in a gas turbine refers to the process of initiating the engine's startup sequence by rotating the turbine's shafts using an external power source, typically an electric motor or a dedicated starting system. This action allows the gas turbine to reach the required speed for fuel ignition and combustion. Cranking is essential for overcoming inertia and ensuring smooth acceleration to operational speeds before the turbine takes over and self-sustains its operation.