0
What else can I help you with?
How does a voltage quadrupler work?
A Voltage Quadrupler would be a DC circuit. A transformer would be used to increase the voltage in an AC circuit. To quadruple the voltage in a DC circuit would consist of (min) 4 resistors. 1 resistor would be directly in parallel with the power source, that is, one side of the R would be connected to one side of the source, and the other side of the R would be connected to the other side of the source. The remaining resistors are configured in a sort of series/parallel with the 1st resistor to increase (ladder fashion) the output voltage. See the related links for a more detailed explntn.
How do you know if you have a single stage or multistage heating and air conditioning system?
Take the thermostats cover off and expose the low voltage wiring, Y or Yellow is the AC circuit, Y1 will be 1st stage cooling, Y2 will be 2nd stage cooling, You may also look at the furnaces low voltage terminals for the various circuits. You will see screws/terminals marked, R /Red, W /White, Y /Yellow, G /Green and C /Common. The R terminal is where the 24 volt "hot leg" of power enters the thermostat , for the thermostat to send the 24 volts to your desired mode/ circuit. W = Heat, Y = Cool, G = Fan and C is the "common" or neutral leg of 24 volt power. Common is akin to the negative on a battery, it is called Common as every 24 volt circuit terminates on Common to complete the circuit. If you had a 2 stage heat system there would be a W1 and a W2. Same with the AC mode. Y1= 1st stage cooling and Y2 = 2nd stage cooling.
What are the basic blocks of generalized instrumentation system?
basically an input is given to the transducer, which is the 1st basic block of instrumentation system. this transducer's o/p goes to the signal conditioning circuit whose o/p is then given to the recorder, analog meter, digital transistor, printer, controller, oscilloscope and the punch card.
What is the Amperes difference between a 2 light bulb series circuit and 2 light bulb parallel circuit?
if the bulbs are identical, we can assume that both of them have the same resistance R. in series : the flowing current is I1, the voltage at the ends of the 1st Bulb is V1 and the voltage at the ends of the 2nd bulb is V2. V1 = V2 = V since they have the same resistance and V is the voltage applied on the ends of the whole circuit. the Total circuit resistance is 2*R. thus : I1 = V / 2*R => V = 2 * I1 * R (1) in Parallel mode : the current flowing in the first bulb is i1 and the current flowing in the second bulb is i2. i1 = i2 since R1 = R2. I2 = i1 + i2 i1 = V / R and i2 = V / R => I2 = (V /R ) + (V / R) = 2*V / R => V = I2 * R / 2 (2) (1) and (2) => 2 * I1 * R = I2 * R /2 => I1 = I2 * R / (R * 2) => I1 = I2 / 2 above, is the mathematical solution of the problem, but the result is directly predictable since both bulbs are identical. in summary the current that flows in the circuit when wired in series is half of the current when wired in parallel. also note, that the voltage in series on the ends of each bulb is half of the voltage when wired in parallel.
What is the position of buet in Bangladesh?
1st position
What does code PO731 mean for a Chrysler intrepid?
PO731 Gear ratio error in 1st gear. Possible causes:Low transmission fluid levelTransmission fluid dirtyDefective shift solenoidsTransmission hydraulic control circuit problemMechanic Problem with transmissionHave the transmission fluid and filter changed and if the problem does not go away seek professional help.
Where is the transmission fluid filter on a 1990 Ford Escort LX?
Drop the transmission pan, the filter will be the 1st thing you see.
Electric circuit analysis annauniversity notes for 1st year?
refer www.estudiez.com
When was the 1st integrated Circuit invented?
In 1958 received a patent by Jack Kilby
Whenever you vacuum your swimming pool the dirt spreads what should you do?
Do you mean that the vac is not picking up the dirt? Do you mean to say that the dirt is returning to the pool via the return lines? 1st question: properly hook up your vac hose and vac head and/or turn on the pump. 2nd question: There is a damaged grid in the D E filter; Wrong type of filter media in a sand filter; Damaged element in a cartridge filter or overpumped- pump is too strong for the system.
What does "1st and 10" mean in American football?
"1st and 10" in American football means that it is the first down and the offense has 10 yards to advance the ball in order to get another first down.
How do you know if it is the fuel pump that is bad or the fuel filter?
try replacing filter 1st not hard still problems check fuel preassure bri
In first order both x and y in chemistry?
what in 1st order?? if you are asking about 1st order chemical equation then there will be only one variable with power 1.
Where in the order of planet is mercury?
1st
Where can you locate the cabin filter inside your 2k Chevrolet Suburban?
1st you insert 3 sticks of dynamite....
Does the 2nd order consumer eat the 1st order consumer?
yes
What is mean 1st 5 natural numbers?
Their mean is 3.
