Electricity, Heat, Natural obstacles during daylight hours
In signal processing, sampling is the reduction of a continuous signal to a discrete signal. A common example is the conversion of a sound wave (a continuous signal) to a sequence of samples (a discrete-time signal).
the low frequency signal which is nothing but the message signalNeither. The envelope will be that of the difference beat frequency. To get the envelope to follow the low frequency input signal you need to mix (multiply) the two signals, not add them.
when the frequency is low , energy will be obviously low. To increase the energy of the signal we need to increase the frequency. This is achieved by multiplying the message signal with the carrier signal (with high frequency).
If you sample at more than the Nyquist frequency (one half the signal frequency) you introduce an aliasing distortion, seen as sub harmonics.
AS FREQUENCY INCREASE THE BANDWIDTH INCREASE. AS WE KNOW NOISE HAVE LARGER BANDWIDTH. SO ITS AFFECT HIGH FREQUENCY SIGNAL. BUT LOW FREQUENCY SIGNAL HAVE LOW BANDWIDTH SO IT IS LESS AFFECTED BY NOISE. ALSO WE KNOW QUALITY FACTOR= CUTOFF FREQUENCY / BANDWIDTH. SO AS FREQUENCY INCREASE B.W. INCREASE SO QUALITY DEGRADE. CUTOFF FREQUNCY AND THE TERM FREQUENCY (USED HERE) IS DIFFERENT. CUTTOFF FREQUNCY IS USED IN FILTER. PRABIR KUMAR SETHY prabirsethy.05@gmail.com
Loudness, pitch and timbre are approximately the correlates of signal amplitude, frequency and frequency spectrum, respectively.
Amplification does not affect the frequency of a signal. It simply increases the strength or magnitude of the signal without changing its frequency. A properly designed amplifier will preserve the frequency content of the input signal while boosting its amplitude.
The frequency performance of a cable is primarily influenced by factors such as its construction (e.g., conductor material, shielding), length, and impedance matching. Additionally, factors like signal attenuation, signal distortion, and crosstalk can also impact the cable's frequency response.
If the amplitude decreases, the frequency remains unchanged. Amplitude refers to the magnitude of the signal, while frequency refers to the number of oscillations per unit of time. Changing the amplitude does not affect the frequency of the signal.
An RLC circuit can affect the amplitude of a signal by either amplifying or dampening it. The circuit can resonate at a specific frequency, causing the amplitude of the signal to increase (in resonance) or decrease (out of resonance) depending on the values of the components. The circuit's impedance at a given frequency dictates how much the signal's amplitude will be affected.
In signal processing, sampling is the reduction of a continuous signal to a discrete signal. A common example is the conversion of a sound wave (a continuous signal) to a sequence of samples (a discrete-time signal).
Frequency does not directly affect amplitude. Amplitude refers to the maximum displacement of a wave from its rest position, while frequency is the number of complete wave cycles that occur in a unit of time. However, in some systems like resonant systems, changes in frequency can affect the amplitude of the wave response.
A radio signal can travel long distances, potentially thousands of miles. The range of a radio signal is influenced by factors such as frequency, power of the transmitter, antenna height, atmospheric conditions, and obstacles in the signal path.
The performance of double diode clippers is influenced by several factors, including the forward voltage drop of the diodes, the load resistance, and the input signal frequency. The forward voltage drop determines the clipping level, while the load resistance affects the output voltage and current characteristics. Additionally, the frequency of the input signal can impact the response time of the diodes, potentially leading to distortion if the signal frequency exceeds the diodes' switching capabilities. Proper circuit design and component selection are essential for optimal performance.
Amplitude of the (high frequency) Carrier signal is varied with respect to low frequency of message signal is called amplitude modulation. Frequency of the carrier signal is varied with respect to low frequency of message signal is called frequency modulation.
the low frequency signal which is nothing but the message signalNeither. The envelope will be that of the difference beat frequency. To get the envelope to follow the low frequency input signal you need to mix (multiply) the two signals, not add them.
The signal with a frequency of 200Hz has a wider bandwidth compared to a signal with a frequency of 100Hz. Bandwidth is determined by the range of frequencies present in a signal, so a higher-frequency signal will have more frequency components and thus a wider bandwidth.