answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

What happens when you remove capacitor in filter circuit?

The capacitors allow the signal to pass through, while 'blocking' the DC voltage level that the signal is 'riding' on. Are you asking to remove the capacitor and connect it straight through? If you had a multistage amplifier, then the DC riding voltage would try to get amplified as well, and the next stage amplifier would probably 'max out' and you'd wind up with just solid DC output, or components further along in the circuit could be damaged. If you're asking if the capacitor was taken out (like if it blew) then no signal would get through.


Why you do not use capacitor in a transistor as switch?

The capacitor is there to block any dc voltage that might be applied to the input terminal, which could cause damage or upset the biassing if it was allowed through to the base.


Frequency response of bjt amplifier?

All amplifier typically exhibit a band-pass frequency response. The cut off frequency in the low end is usually determined by the coupling band bypass capacitor .and the high frequency limit is typically determined by internal capacitances in the transistor itself.


What is the effect of bypass capacitor on frequency response?

Gain in a CE configuration of a BJT is collector resistance divided by emitter resistance, subject to the limit of hFe. The emitter bypass capacitor will have lower impedance at high frequency, so the gain will be higher at higher frequency, making this a high-pass amplifier.


What is the purpose of a coupling capacitor?

A coupling capacitor does the same work as its name suggests, that is coupling one stage of the electronic circuit with another. It does that without passing the DC bias voltages between stages so that these stages are not affected by each other.To block or avoid the flow of D.C and to allow only A.C

Related Questions

Why we use blocking and by pass capacitor in CE amplifier?

As the DC component in the signals are not required to be amplified, rather not required at times. Thus a blocking capacitor blocks this DC component from.entering the amplifier. Bypass capacitors are used at the emitter end so that the AC signal reaching the emitter end does not alter the biasing required to maintain the Q-point. All the above happens using the basic characteristic of a capacitor, that it blocks DC and passes AC.


What is the effect on voltage gain in a common emitter amplifier when the decoupling capacitor is removed?

The emitter bypass capacitor, in a typical common emitter configuration, increases gain as a function of frequency, making a high pass filter. Removing the capacitor will remove the gain component due to frequency, and the amplifier will degrade to its DC characteristics.


What happens when you remove capacitor in filter circuit?

The capacitors allow the signal to pass through, while 'blocking' the DC voltage level that the signal is 'riding' on. Are you asking to remove the capacitor and connect it straight through? If you had a multistage amplifier, then the DC riding voltage would try to get amplified as well, and the next stage amplifier would probably 'max out' and you'd wind up with just solid DC output, or components further along in the circuit could be damaged. If you're asking if the capacitor was taken out (like if it blew) then no signal would get through.


Why capacitor in transistor amplifier circuit at input?

Because capacitor not allow to pass dc voltage,but capacitor allow ac voltage and signal.Purpose is to block dc voltage.That is coupling condenser.


Can you by-pass a capacitor in an electric motor?

You can not by-pass the capacitor in an electric motor. Most are capacitor-start motors which require the capacitor to be operational in order to start. If the capacitor is not working then it will need to be replaced.


Why you do not use capacitor in a transistor as switch?

The capacitor is there to block any dc voltage that might be applied to the input terminal, which could cause damage or upset the biassing if it was allowed through to the base.


What is the function of emitter bypass capacitor in common emitter amplifier?

The emitter bypass capacitor in a common emitter amplifier will have less resistance as the frequency increases. Since gain in this configuration is collector resistance divided by emitter resistance (within limits of hFe), the gain will thus increase for higher frequencies, making this into a high pass filter.


Frequency response of bjt amplifier?

All amplifier typically exhibit a band-pass frequency response. The cut off frequency in the low end is usually determined by the coupling band bypass capacitor .and the high frequency limit is typically determined by internal capacitances in the transistor itself.


What is a tuned amplifier?

an amplifier with a narrow band pass used to tune into a carrier signal.


What is the effect of bypass capacitor on frequency response?

Gain in a CE configuration of a BJT is collector resistance divided by emitter resistance, subject to the limit of hFe. The emitter bypass capacitor will have lower impedance at high frequency, so the gain will be higher at higher frequency, making this a high-pass amplifier.


What does the capacitor in a low pass filter do?

Does not allow high frequencies to pass through the circuit.


What is a filter capacitor?

Capacitor has many applications in electronics circuits, one of its application is in FILTERS. Mainly two types of Filters are formed with the help of capacitor namely, i)Low Pass Filter(LPF) ii)High Pass Filter(HPF) Impedance of capacitor is inversely propotional to the frequency, therefore a capacitor in series with resistor will act as Low Pass Filter. since all the high frequency are passed to ground.