answersLogoWhite

0

It will work properly! The resistance and impedance of the earth lead must be low, though the corollary is that it must be capable of passing any likely fault current safely.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

How we get 0.5 ohm resistance for Earth pit?

Type your answer here... how to get ohm in earth pit


When is earthing required?

As it's a safety factor, earthing is essential and mandatory. It's an electrical connection between the exposed metallic parts of an electrical appliance or installation and the earth, regarded to have zero potential. Proper earthing provides an alternative and easy path for leakage or faulty current to flow. It ensures that any exposed conductive part of the appliance does not reach a dangerous level of potential or voltage that endangers the user's life. A proper earthing system should have least electrical resistance, good corrosion resistance and ability of dissipating high faulty current.


How do you test neutral earthing compensator and resistor?

Testing a neutral earthing compensator and resistor typically involves measuring the resistance of the earthing system using a megohmmeter, ensuring it falls within specified limits. Additionally, the functionality of the compensator can be verified by simulating fault conditions to observe its response and effectiveness in limiting fault currents. Regular inspections for physical damage or corrosion, as well as testing for continuity and insulation resistance, are also essential to ensure reliability and safety.


What is the difference between insulation resistance and earth resistance?

insulation resistance can be measured by means of megger, with built in d.c generator. It is measured between the conductor and the earth. earth resistance can be measured by means of earth resistance tester. For good effective earthing, th earth resistance should be of order 0.5 ohm


What is the difference between earthing boss and earthing lug and where to use?

An earthing boss and earthing lug are parts of a grounding connection. An earthing boss is in a casting that allows for the drilling and tapping of hole. A earthing lug is used to bond a wire to the ground.

Related Questions

What happens to the power of an electric circuit of the resistance is decreased?

if the resistance is decreased and the current stays the same, then the power decreases.


What happens to resistant if wire diameter is decreased?

If the wire diameter is decreased, the resistance of the wire will increase. This is because with a smaller diameter, there is less cross-sectional area for the electrical current to flow through, causing more hindrance and resulting in higher resistance.


How we get 0.5 ohm resistance for Earth pit?

Type your answer here... how to get ohm in earth pit


What happens to resistance if radius of a wire is decreased by a factor of 3?

If the radius of a wire is decreased by a factor of 3, the resistance of the wire will increase by a factor of 9. This is because resistance is inversely proportional to the cross-sectional area of the wire, which is proportional to the square of the radius. So, decreasing the radius by a factor of 3 will result in the area decreasing by a factor of 9, leading to a 9-fold increase in resistance.


What happens when one bulb is added to a series circuit?

The resistance is increased, the voltage across each bulb is decreased and the current through the circuit is reduced.


To avoid arcing connect sutable value of in earthing?

To avoid arcing, it is important to connect a suitable value of grounding or earthing. This helps to provide a path of low resistance for any electrical faults or surges, diverting the excess current away from sensitive equipment or components. The appropriate value of grounding or earthing can vary depending on the specific electrical system, so it is important to consult with a professional to determine the correct value for your setup.


Why does an thick earthing wire?

A thick earthing wire, or a wide, flat conductor, is preferred, because it's more important to minimize henrys (inductance) in the earthing system than to reduce ohms (resistance). For the same reason, corners and small angles in an earthing conductor should be avoided, and the conductor should approach any connections from a parallel direction.


What is the difference between chemical earthing and conventional earthing?

Chemical Earthing and Conventional Earthing are different types of earthing techniques. Conventional Earthing is based on plate earthing and pipe type earthing but Chemical Earthing on GI or Copper.


What should be the earth resistance of a good earth?

The lower the resistance you get in the grounding/earth system the better. In offshore a resistance from 1-2 ohm is a good earthing system. In Onshore a miximum of 10ohm is acceptable.


Why should a earthing circuit have low resistance?

Oh, dude, like, you want that earthing circuit to have low resistance so it can quickly divert any unwanted electrical currents to the ground, you know? It's like giving those pesky electrons a speedy highway to escape instead of causing chaos in your appliances or, worse, in you! So yeah, low resistance in the earthing circuit is crucial for safety and keeping things running smoothly.


What are the types of electrical earthing with respect to Electrodes?

Electrical earthing is classified into many types as Neutral earthing Body earthing Pipe earthing Plate earthing Chemical earthing Ground Compound Earthing


How can air resistance be decreased?

Air resistance can be decreased by making the object more aerodynamic, such as by reducing its size or shaping it to minimize drag. Smooth surfaces and streamlined designs help to reduce turbulence and resistance. Additionally, reducing the object's speed can also decrease air resistance.