answersLogoWhite

0

Mine has neither and it works perfectly I install this type all the time

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

What is the function of a toilet flapper?

The toilet flapper is a crucial component of a toilet's flushing mechanism. It acts as a valve that seals the tank and prevents water from flowing into the bowl until the toilet is flushed. When the flush lever is activated, the flapper lifts, allowing water to rush from the tank into the bowl, creating the flush. Afterward, the flapper closes, refilling the tank for the next use.


How do you replace a flapper in a toilet?

Shut the water supply off to the toilet. Flush the toilet. Pull the old flapper out and replace it with the same type. Turn the water back on and test the toilet.


Where would you most likely find a flapper in plumbing and what would it most likely be used to do?

A toilet flapper is found inside the tank of a toilet. It is a rubber stopper that rests over the water outlet. As the bowl is flushed, the apparatus lifts the flapper over the drain outlet hole. As the bowl and tank refills, the apparatus drops the flapper so it is again seated over the drain hole. Once the water in the tank reaches a certain level, the water automatically stops. Note: If your toilet constantly runs, most likely the flapper has not completely seated itself in the hole. Hard water can cause mineral deposits around the drain which prevents the flapper from seating properly. Also the rubber can become old and leak around the edges.NOTE: Not to be confused with 1920s "flappers", women who dressed in short skirts, gaudy jewelry and headbands, and were fond of dancing.


Why does a flapper close to early on a toilet?

Wrong adjustment


What is the average life of a toilet flapper?

5 years

Related Questions

What is the purpose of the flapper inside of a toilet tank?

The purpose of the flapper inside a toilet tank is to control the flow of water from the tank into the toilet bowl when the toilet is flushed.


What is the purpose of the flapper inside the toilet tank?

The purpose of the flapper inside the toilet tank is to control the flow of water from the tank into the toilet bowl when the toilet is flushed.


What are the steps to install a new toilet flapper in a toilet tank?

To install a new toilet flapper in a toilet tank, first turn off the water supply to the toilet. Flush the toilet to empty the tank. Remove the old flapper by disconnecting it from the flush valve. Install the new flapper by attaching it to the flush valve. Turn the water supply back on and test the new flapper by flushing the toilet.


What is the purpose of a flapper seal in a toilet tank?

The purpose of a flapper seal in a toilet tank is to create a watertight seal between the tank and the bowl, preventing water from leaking out of the tank when the toilet is flushed.


What is the purpose of the toilet tank flapper and how can it be replaced if it is not functioning properly?

The purpose of the toilet tank flapper is to control the flow of water from the tank to the bowl when the toilet is flushed. If the flapper is not functioning properly, it can be replaced by turning off the water supply to the toilet, removing the old flapper, and installing a new one in its place.


Why does the toilet flapper stay up?

The toilet flapper stays up to allow water to flow from the tank into the bowl when the toilet is flushed.


What is a flapper on a toilet and how does it function in the flushing mechanism?

A flapper on a toilet is a rubber or plastic seal that covers the opening at the bottom of the toilet tank. When the toilet is flushed, the flapper lifts up to allow water to flow from the tank into the bowl, causing the toilet to flush. After the flush is complete, the flapper falls back down to seal the opening and prevent water from leaking out of the tank.


How can I change the flapper in a toilet tank?

To change the flapper in a toilet tank, first turn off the water supply to the toilet. Remove the old flapper by disconnecting it from the flush valve. Install the new flapper by attaching it to the flush valve. Turn the water supply back on and test the toilet to ensure the flapper is working properly.


How does a flapper valve toilet work to regulate the flow of water in a toilet system?

A flapper valve toilet works by using a rubber flapper to control the flow of water from the tank into the bowl. When the toilet is flushed, the flapper lifts up, allowing water to rush into the bowl. Once the tank is empty, the flapper closes, stopping the flow of water and refilling the tank for the next flush.


How can I fix a toilet tank that will not refill?

Check the flapper and/or the ball cock assembly. Either or both probably need to be replaced.


Why does the toilet run constantly and how can it be fixed?

A toilet runs constantly when there is a leak in the tank or the flapper is not sealing properly. To fix it, you can adjust the flapper chain, replace the flapper, or check for any leaks in the tank and repair them.


What is the function of a toilet flapper?

The toilet flapper is a crucial component of a toilet's flushing mechanism. It acts as a valve that seals the tank and prevents water from flowing into the bowl until the toilet is flushed. When the flush lever is activated, the flapper lifts, allowing water to rush from the tank into the bowl, creating the flush. Afterward, the flapper closes, refilling the tank for the next use.