Sometimes it can take up to TWO MINUTES for the thermocouple to take effect ( proof of flame) If the flame does not stay on the thermocouple should be replaced by a qualified licensed plumber
about a half hour
No. Once a water heater tank leaks there is no fixing it. Just replacing the water heater. And it should probably done as soon as possible, since the potential for a bigger leak to open is very possible.
Well I found if I do not take it for granted and buy it a present once in a while and possibly sing to it it will turn on after a while
The water pressure in my house is about 140PSI. Which is definitely dangerous. It happens more often than you would think. What happens is a city will use water supply lines which are too small for the water requirements. Therefore, they have to increase the pressure. You wouldn't want a pressure relief valve, because then if the pressure was too high, it would just spray water everywhere to release the pressure. You would want a pressure regulator installed, which is what I am working on for my house right now. Just to let you know though, you may have to get a thermal expansion tank for your water heater if you don't have one. See, the new pressure regulators have a check valve in them, which prevents water from traveling back into the city pipes once it has gotten into your house. When your water heater heats the water, the air bubbles in it expand, which increases the water pressure, and will probably cause your pressure relief valve on your water heater to blow. You can get a cheap water pressure meter at any improvement store to check it out. 50-60 PSI is ok. I would say you could take it up to 70 or 80 PSI safely.
Here are a few things to check: Does the pilot light stay on after you light it? If so, good, did you turn the control valve to the "on" position? Sounds funny but there's a pilot position and a "on" position. Is the pump on? Water must be circulating through the heater to activate a pressure switch & then the burner will come on. If not find the manual on position for your pump timer to start the pump. Burner still doesn't come on? Check the burner assembly for plugged orifices (i.e. spiders, corrosion, etc.)and clean it out. The following is a more detailed and complete walk through, analysis :- Swimming Pool Heaters have a number of safety controls. Before the heater will turn on, all the safety switched must be "Closed", that is to say the electrical circuit is complete. But my heater doesn't have electric going to it you say ?? The Pilot light flame is directed towards a device that looks like an AA battery with 2 wires coming out the bottom. This is called a "Thermo-pile", ( from the French word "pile", meaning Battery.) This Thermo-pile creates electricity (DC, +/- 750 mV) which is the electricity that once it passes all the safety switches makes its way to the main gas valve and lifts the gas valve to Open and let the gas through to be ignited. Some of the safety switches are : Pressure switch. This is an important water pressure operated switch that tells the heater that there is water flowing through the heater. ( If your filter needs backwashing, and flow is poor -this switch will stay "Open" and not allow the heater to turn on. On/Off Switch... If I need to explain this - stop reading and call a Gas Appliance Professional. Thermostat : This is the rotary temperature Dial that senses the water temperature Fusible Link. : Often mounted on the front inside of the Cabinet, just above the Heater tray, this switch senses if flames are coming out the front of the cabinet. -If the fusible Link blows (a) it needs to be replaced and (b) FIND OUT WHY!! Flames and heat should go straight up, if they are coming laterally out the front of the heater then the heater is not venting properly and you need to know why. Common causes are (i) on a heater with a Flat Top, and no Stack (Chimney), a gust of wind or a downdraft caused by winds bouncing off an adjacent structure or wall can cause the flames to roll out the front momentarily. (ii) If the heater has been incorrectly installed with insufficient gas pressure, volume available to the Main valve, then incomplete combustion occurs, and the sooty smoke can clog the heat exchanger fins, which impedes the venting of the heater and the flames roll out the front. "Tired " Thermo-Pile. The Thermo-Piles lose their ability to produce current over time, and the Thermo-Pile may be generating enough power to keep the pilot lit, but not enough to open the main valve. There are other switches and safety's that vary on model and the installation, but the above information should solve 99% of problems. Remember, we are dealing with a very minute current here. If any of the wire terminals are loose or corroded, that will reduce the efficiency of the electrical circuit and cause sufficient loss of power that the Main Gas valve will not open. Good Luck MaDoGreg IF YOU HAVE TO LOOSEN OR OPEN ANY GAS CONNECTIONS, YOU MUST TEST THEM WITH SOAPY WATER AFTER RE-CONNECTION TO ENSURE THERE IS NO GAS LEAK. If in doubt, call a trained professional ! Greg M Simmons, C.P.O. East Hampton, NY 1-631-831-5017 gregs.cpo@gmail.com
To start a gas water heater, first make sure the gas supply is turned on. Then, locate the pilot light and follow the manufacturer's instructions to relight it. Once the pilot light is lit, adjust the temperature setting on the water heater to your desired level. Allow the water heater to heat up the water before using it.
To turn on the water heater pilot, locate the pilot light button or knob on the water heater. Turn the knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about a minute before releasing it. This should successfully turn on the water heater pilot.
To turn on the pilot light for your water heater, locate the pilot light assembly near the bottom of the water heater. Turn the gas control knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about 30 seconds before releasing it. If the pilot light stays lit, turn the gas control knob to the "on" position to start the water heater.
It's possible hard water deposits have built up inside. To prevent this and the early demise of your water heater, drain and flush the heater at least once a year.
To turn on a gas water heater, locate the pilot light and turn the knob to the "pilot" setting. Press and hold the knob down while using a long lighter to ignite the pilot light. Once lit, continue holding the knob down for about 30 seconds before releasing it. Then, turn the knob to the "on" position to start the water heater.
I once had a caravan fitted with an instantaneous water heater.
To turn on the pilot light on your water heater, locate the pilot light access panel on the water heater. Follow the manufacturer's instructions for lighting the pilot light, which usually involves turning the gas control knob to the pilot position, pressing and holding the knob down, and using a long lighter to ignite the pilot light. Once lit, continue holding the knob down for a few seconds before releasing it. Make sure to follow all safety precautions and guidelines provided by the manufacturer.
It is recommended to drain your water heater at least once a year to remove sediment buildup and maintain its efficiency.
A check valve in a water heater system prevents water from flowing back into the system once it has been heated and circulated, helping to maintain consistent water pressure and prevent damage to the water heater.
To safely relight the hot water heater pilot light in your home, follow these steps: Turn off the gas supply to the water heater. Wait for the gas to dissipate for at least 5 minutes. Locate the pilot light assembly and follow the manufacturer's instructions for relighting. Use a long lighter or match to ignite the pilot light. Once the pilot light is lit, turn the gas supply back on. Check for any gas leaks by using a soapy water solution on the connections. If you smell gas or encounter any issues, contact a professional for assistance.
You should perform maintenance on your water heater, including cleaning it, at least once a year to ensure it functions efficiently.
Yes, it is recommended to flush your water heater regularly for maintenance purposes. Flushing helps remove sediment buildup, which can improve the efficiency and lifespan of your water heater. It is typically recommended to flush your water heater at least once a year.