answersLogoWhite

0

American Wire Gauge. Measure the thickness of the cable.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

What AWG cable for 200' x 208 volt three phase 250 amp circuit?

A wire size of 250 MCM will limit the voltage drop to 3% over a distance of 200 feet.


How many amps can 25mm sq electrical cable can carry?

A 25mm sq electrical cable is equal to a #4 AWG conductor. A #4 copper conductor with an insulation factor of 75 and 90 degrees C is rated at 85 and 95 amps respectively.


What is the size of the cable used for ear buds?

The size of the cable used for earbuds typically ranges from 26 to 30 AWG (American Wire Gauge). This gauge is thin enough to maintain flexibility and comfort while being adequate for transmitting audio signals. The actual diameter may vary slightly depending on the manufacturer and design, but this range is common for lightweight earbud cables.


Wire size for a 15 KVA transformer?

Primary : 4 Secondary : 3/0 <<>> To answer this question correctly a voltage must be stated.


What is the difference between 12.2 and 12.3 wire?

The 12 refers to the size of wire in AWG - American Wire Gauge. 12 gauge wire can legally carry 20 Amps, and would be used if the circuit breaker is 20 A. 14 AWG can carry 15 Amps, used on a 15 A breaker. The 2 or 3 refers to the number of ungrounded conductors in a cable (such as romex or NM). 12-2 would contain a hot (black) and a neutral (white). 12-3 would contain two hots (black and red), and a neutral (white). Additionally, these cables are available "with ground," meaning a bare ground wire is added to the cable. So a "12-2 with ground" would actually contain three conductors including the bare ground wire. A 12-2 with ground cable would be used where you needed to run a single 20 A circuit. You are allowed to share a ground and neutral when running two circuits if the circuits are on different legs (phases) in the panel. 12-3 is used for this purpose. It can also be used where you need 240 volts (between the black and red) with a neutral (and ground).

Related Questions

Can you use a 4 awg cable if the old cable is a 6 awg cable?

Yes, you can use a 4 AWG cable to replace a 6 AWG cable, as the 4 AWG cable has a larger diameter and can handle more current. However, it's important to ensure that the new cable is compatible with the existing circuit's rating and that it meets local electrical codes. Additionally, you should verify that the connectors and overcurrent protection devices are appropriate for the larger cable size. Always consult a qualified electrician if you have any doubts.


What is the awg wire size designation of the cable?

:D


What is the recommended cable size for a 200 amp service entrance cable?

The recommended cable size for a 200 amp service entrance is typically 2/0 AWG copper or 4/0 AWG aluminum.


Is 12awg speaker cable thicker than 14awg speaker cable?

Yes, 12 AWG (American Wire Gauge) speaker cable is thicker than 14 AWG cable. The lower the AWG number, the thicker the wire, which allows for lower resistance and better conductivity. This can be beneficial for longer runs or higher power applications, as it helps minimize signal loss.


What is the recommended cable size for a 100 amp electrical circuit?

The recommended cable size for a 100 amp electrical circuit is typically 3 AWG copper or 1/0 AWG aluminum.


What is the recommended size for a 100 amp service entrance cable?

The recommended size for a 100 amp service entrance cable is typically 2 AWG copper or 1/0 AWG aluminum.


What is the correct size of cable to used for 50 amps?

8 AWG.


How much current does 20 AWG cable carry?

30 Amps


What size aluminum cable for 100 amp service?

2 AWG Aluminum.


What size aluminum entrance cable for 100 Amp service?

2 AWG Aluminum.


What type of service entrance cable should be used for a 100 amp electrical service?

For a 100 amp electrical service, a service entrance cable of at least 2 AWG copper or 1/0 AWG aluminum should be used.


What is the wire that comes out of the positive battery cable attachment on my 1990 Isuzu Trooper?

If it's a heavy gauge (around 8 AWG IIRC), that's the charge wire to the alternator BATT post. The larger cable (about 4 AWG) goes to the starter.