0
What else can I help you with?
What pipe has the smallest id schedule 40 schedule 80 or schedule 160?
For a given pipe size, schedule 160 would have the smallest ID (and thicker wall). Wall thickness and pressure rating goes up with increasing schedule number, causing the ID to go down with increasing schedule number.
What is flow rate for copper pipe?
1/2 OD or ID as copper is measured by OD BUT in plumbing rather then saying 5/8 L tubing we say 1/2 BUT 1/2 in ACR work is actually plumbers 3/8 The flow rate is about 7.5 to 10gpm Plenty for up to 3 low flow shower heads.
How do you find the bearing number of a ball bearing?
The bearing number can be checked out depends on the size of ID (Inner Diameter), OD (Outer Diameter) and H (Height) of this bearing.
What is id selector?
The id selector uses the id attribute of an HTML element to select a specific element. To select an element with a specific id, write a hash (#) character, followed by the id of the element.
How do you figure drill pipe capacity?
To determine drill pipe capacity, you need to calculate the volume of fluid that can be held within the pipe. This is done by using the formula: Capacity (gallons) = (π/4) × (OD² - ID²) × Length × 0.0034, where OD is the outer diameter, ID is the inner diameter, and Length is in feet. The result gives you the capacity in gallons, considering both the outer and inner dimensions of the pipe. Additionally, it's important to account for any fittings or connections that may affect the overall capacity.
Is copper tubing measured in ID or OD?
Copper tubing is typically measured by its outside diameter (OD). This measurement is important for compatibility with fittings and other plumbing components. However, in some contexts, especially in HVAC and refrigeration, the inside diameter (ID) may also be referenced for specific applications. Always check the specifications for the intended use to ensure proper fit and function.
What is the standard size for a photo ID card?
The standard size for a photo ID card is 3.375 inches by 2.125 inches, which is the same size as a credit card.
Is galvanized pipe measured id or od?
Galvanized pipe is typically measured by its nominal pipe size (NPS), which refers to the inside diameter (ID) of the pipe. However, the actual dimensions can vary, and the outside diameter (OD) is also standardized. It's important to check the specific standards for the type of pipe being used, as the measurements can affect fittings and connections.
What size is s in the UK?
'S' size id 36 - 37 in UK
How do you calculate the plate size for a dish end?
Id+kr+2sf=blank size
What size motor did the 84 dodge D150 prospector have?
the Prospector had either a 318 cu id or a 360 cu id engine.
Copper is an important trace element responsible for red blood cell formation, enzyme function, andcollagen formation. On your Periodic Table, the atomic mass of copper is 63.546 amu.Which of the following is a true statement about copper?
You did not put any, but id say oxidization
How old do you have to be to sell copper?
You have to be 18 and they ask for an ID. I took some metal into a recycling place and they even took a finger print.
Why does your hair turn blue after going in spa?
Id say its more than likely the chemicals they use or an abundance of copper in the water. Sometimes copper is added when they use cheap chemicals to control algae. It can also be from too low a pH and copper piping being erroded.
What is the ampacity of a NM-B cable?
Allowable ampacity for 10-2 copper NM-B is 30 A.http://www.cerrowire.com/default.aspx?id=46
How do you find the content file size in documentum?
select r_object_id, r_content_size from dm_document where r_object_id='<id>'
Average breast size for a twelve year old?
Id say anywhere from 30A-36B
