0
What else can I help you with?
Why is the theoretical value for modulus of elastricity for mild steel is different from the calculated value?
because it is the ratio of the stress to the strain and in actual condition the strain developed is different from the theoretical .
Why you need to find stress in steel?
stress on steel need to be calculated because elastic limit is not be exceeded basically we have to work within the elastic region in a stress cycle diagram.
What is the ultimate stress of mild steel?
Allowable stress would normally refer to design using Allowable Strength Design, also known as working strength design. In this the allowable stress is usually a fraction of the yield strength and can be different for uniform tension and bending. Typically mild steel has a yield strength of about fy=250MPa with allowable stresses in Tension, 0.6fy=150MPa Bending, 0.66fy=165MPa
What is the definition of working stress in strength of materials?
it is defined is the stress in the material(steel,Al,etc) that will not be exceeded under normal operating condition
How do you check mild steel and carbon steel?
through a utm machine tensile force is act on both bodies and check stress strain diagram and then eaisly find that who is steel and who is carbon
What is mild steel tensile stress value in newton per square mm?
Mild steel tensile stress of 370 to 520 Newtons per square millimeter.
Is steel elastic and can it be deformed under stress?
Yes, steel is elastic and can be deformed under stress.
Strain-stress diagram of copper and steel?
difference between Strain-stress diagram of copper and steel?
Why is the theoretical value for modulus of elastricity for mild steel is different from the calculated value?
because it is the ratio of the stress to the strain and in actual condition the strain developed is different from the theoretical .
What is yield stress value for frp?
3000 MPa ultimate tensile strength (more than 10 times mild steel)
What is the factor of safety value for working stress method?
for concrete a F.O.S. upto 3 is used . and for steel 1.75 to 1.85 .. is used.
What is the Young's modulus value for steel and how does it affect the material's mechanical properties?
The Young's modulus value for steel is typically around 200 GPa. This value represents the material's stiffness or resistance to deformation under stress. A higher Young's modulus indicates that the material is stiffer and less likely to deform when subjected to external forces. This property affects the mechanical properties of steel by influencing its ability to withstand loads, resist bending, and maintain its shape under stress.
What is the effect of annealing on tensile of steel?
Reducing stress in the steel.
Why you need to find stress in steel?
stress on steel need to be calculated because elastic limit is not be exceeded basically we have to work within the elastic region in a stress cycle diagram.
Yield stress of tool steel?
The yield stress of tool steel is the amount of stress that a material can withstand without experiencing permanent deformation. The yield stress of a specific type of tool steel can vary depending on the specific composition and manufacturing process of the steel. In general, tool steels have high yield stresses, typically in the range of 1000 to 2000 megapascals (MPa). This allows them to withstand high levels of stress and strain without deforming permanently. For example, the yield stress of high-speed steel (HSS) can be in the range of 1500 to 2000 MPa, while the yield stress of cold-work tool steel can be in the range of 1200 to 1600 MPa. Overall, the yield stress of tool steel is an important property that determines the material's ability to withstand high levels of stress and strain without deforming permanently.
What SA-212 Grade B stress value?
SA212-Grade B was a type of steel used in building during the midcentury. It had a basic allowable stress of 17,500 psi up to 650 degrees (F).
What is the shearing strength of mild steel?
Compressive Stress for mild steel (IS 2062 Gr.B - ASME SA 36 is 407.7 MPa This is what I think is the value. If there are different valuses please send me a amil. ramsrini16@yahoo.com Dr.S.RAmachandran, NIOT , Chennai.
