answersLogoWhite

0

overload heater is used to protect a large electric motor. If the overload heater get too hot from excessive current. its nomally-closed overload contacts wil open. interruptting the circiut of powe supply of motor

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

Where would power factor capacitors be installed on a 3 phase motor?

Power factor capacitors can be installed on a three phase motor between the motor contactor and the overload heater block.


What is the inverse time of the thermal overload?

what is the inverse time of the theraml overload?


What is the cause of the compressor if not trip to its overload?

What is the cause of a compressor if not trip to its overload


What melts if the current in an electric circuit gets too high?

Anything that is in contact with the medium conducting the over-current. In an ideal situation a breaker should trip or a fuse should blow. If not wire insulation can melt, the wire itself can melt or various components can either melt or burn outright. Sq D used a motor overload heater that was used on its motor overload contactor. It was designed as a ratchet on the end of a shaft that was inserted in a barrel on the body of the overload. A melting alloy held the shaft in the barrel. The ratchet on the end of the shaft held a spring loaded contact in the closed position. The body of the overload was bolted in series with the load terminal on the output side of the contactor. When the motor load current heated the overload protection device above its trip point, the alloy melted allowing the shaft to turn in the barrel portion of the overload heater. Being spring loaded the ratchet turned from the spring pressure and opened the normally closed contact thereby opening the magnetics coil circuit, dropping the contactor open and shutting the motor off.


What is transient overload?

Sustained overload is overload that is continuous, or permanent. A resistive load is a good example. This is the kind of overload you get from simply plugging too many items into a circuit. Transient overload is overload generated by a reactive load, a momentary short circuit, or other temporary condition. An example of a reactive load is the compressor of an air conditioner starting. This kind of overload can be caused by a reactive load being added to an already moderately loaded circuit.

Related Questions

Can you safely use an extension cord with a space heater?

No, it is not safe to use an extension cord with a space heater as it can overload the cord and pose a fire hazard. It is recommended to plug the space heater directly into a wall outlet.


Why does my space heater trip the breaker?

Your space heater may trip the breaker because it draws too much power, causing the circuit to overload and the breaker to shut off to prevent a fire hazard.


Is it safe to plug a space heater into a heavy duty extension cord?

No, it is not safe to plug a space heater into a heavy-duty extension cord as it can overload the cord and pose a fire hazard. It is recommended to plug the space heater directly into a wall outlet to ensure safety.


When was Overload - Overload album - created?

Overload - Overload album - was created in 2006.


Why does my space heater keep tripping the breaker?

Your space heater may be tripping the breaker because it is drawing too much power and causing an overload on the circuit. This can happen if the heater is plugged into a circuit that is already handling a heavy load or if the heater itself is faulty. It is important to make sure the heater is plugged into a dedicated circuit and not sharing power with other high-wattage devices. If the issue persists, it may be a good idea to have the heater inspected by a professional.


What is the difference between overload trip and over current trip. if there is an overload trip the current will be raised above the set point?

An overload trip is due to too much load on a circuit (for example, my wife running a hair dryer and portable heater on the same outlet). An over current trip is the same thing, but it can also refer to an actual fault condition where conductors have come in contact with eachother/shorted.


Is it safe to plug a heater into an extension cord?

It is generally not safe to plug a heater into an extension cord because heaters draw a lot of power and can overload the cord, potentially causing a fire hazard. It is recommended to plug heaters directly into a wall outlet to ensure safety.


Where would power factor capacitors be installed on a 3 phase motor?

Power factor capacitors can be installed on a three phase motor between the motor contactor and the overload heater block.


What can we do if our Curcuit breaker tripped on the heater and will not reset?

If your circuit breaker has tripped and will not reset after a heater overload, it is essential to disconnect the heater from the circuit and try resetting the breaker again. If the breaker continues to trip, there may be a more significant issue with the heater or the circuit, and it is recommended to contact a licensed electrician to assess and repair the problem to prevent any potential hazards.


Is it safe to plug a space heater into an extension cord?

It is generally not safe to plug a space heater into an extension cord. Space heaters draw a lot of power and can overload the extension cord, leading to a fire hazard. It is recommended to plug space heaters directly into a wall outlet to ensure safety.


When was System Overload created?

System Overload was created in 2006.


When was Overload - magazine - created?

Overload - magazine - was created in 1993.