answersLogoWhite

0

A sensor that measures flow and pressure of the fluid in a hydraulic system.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Where is john Deere hydraulic oil sensor location?

The hydraulic oil sensor on a John Deere machine is typically located near the hydraulic oil reservoir or within the hydraulic system itself. Depending on the model, it may be found on the hydraulic filter, the pump, or attached to the hydraulic manifold. For precise location details, it's best to consult the specific operator's manual for your John Deere equipment model.


What does error code 1T mean on a Raymond forklift?

Error code 1T on a Raymond forklift typically indicates a problem with the truck's tilt function, often related to the tilt sensor or the hydraulic system. This error may arise from issues such as sensor malfunction, low hydraulic fluid levels, or electrical faults. To resolve the issue, it's advisable to check the tilt sensor connections, inspect the hydraulic fluid, and consult the forklift's manual or a qualified technician for further diagnostics.


What does code P0935 mean?

Trouble code P0935 means: Hydraulic pressure sensor circuit high input


Where is the location of hydraulic pressure sensor of 4jx1 common rail fuel system?

The location is where the oil rail and the injectors and the camshafts are the sensor is conected direct to the rail . You have to remove the aluminum intercooler , the plastic cover , and the aluminum cover to see the sensor .


What is Volvo fault code 11 for ec330b excavator?

Volvo fault code 11 for the EC330B excavator typically indicates a problem with the machine's hydraulic system, specifically related to the hydraulic oil temperature sensor. This code may suggest that the hydraulic oil temperature is too high or that there is a malfunction in the sensor itself. It’s important to check the hydraulic fluid levels, inspect for leaks, and ensure proper cooling to resolve the issue. If the problem persists, consulting the service manual or a professional technician is recommended for further diagnosis and repair.


How do you top up the hydraulic fluid in a vw mk 1 golf convertible?

To top up the hydraulic fluid in a VW MK 1 Golf, you need to locate the hydraulic fluid reservoir attached to the brake master cylinder. Unplug the electrical fluid sensor and Fill the reservoir to the ÒMaxÓ mark.


What is a governor sensor and where is it found on trans.?

A governor and sensor are usually two different devices. The Governor is a hydraulic valve that is spun up by the output shaft and changes the pressure inside the valve body to direct shift speeds A sensor is used for the same purpose in computer shifted units. But I have never heard of a governor sensor.


What could be the cause when a Honda civic abs light stays on?

HAVE A MECHANIC SCAN YOUR ABS SYSTEM THROUGH THE ECM. IT IS MOST LIKELY A FAULTY WHEEL SPEED SENSOR OR MAY BE THE ABS HYDRAULIC MODULATOR ITSELF. HAVE A MECHANIC SCAN YOUR ABS SYSTEM THROUGH THE ECM. IT IS MOST LIKELY A FAULTY WHEEL SPEED SENSOR OR MAY BE THE ABS HYDRAULIC MODULATOR ITSELF.


What is the best way to get to the speed sensor on a 1999 concord?

There are two speed sensors on the car. The output speed sensor is located on the transmission near the middle of the car. To get to it, the car must be lifted, either by jacks or a hydraulic lift at an auto shop. The sensor is basically under the center console of the car.


What is error code e 31 on Nissan forklift?

Error code E31 on a Nissan forklift typically indicates a problem with the lift's tilt sensor or the tilt cylinder. This can occur due to faulty wiring, a defective sensor, or issues within the hydraulic system. To resolve the issue, it's recommended to inspect the tilt sensor connections and the hydraulic components for any signs of damage or wear. If necessary, consult the forklift's service manual or a qualified technician for further diagnosis and repair.


How does a ride height sensor on c Cadillac deville work?

There is a ball joint on the lower control arms of the suspension that allows a rod to connect to a ride height sensor and this is how it figures out what the suspension is doing and it uses a hydraulic system to change the suspension.


Can I use hydraulic fluid for a substitute for hydraulic oil in a bobcat skid-steer?

Hydraulic fluid and hydraulic oil are one in the same.