0
What else can I help you with?
What do you mean by seam welding where it is used?
seam welding is a process that produces a weld at the faying surfaces of two similar metals where its used depends on which metal you look to weld
How many weld passes does it take to fill a one deep weld seam?
The number of weld passes required to fill a one-deep weld seam typically depends on factors such as the joint configuration, material thickness, and welding technique used. Generally, for a single groove weld, it often takes one to three passes to achieve full penetration, but this can vary. In some cases, multiple passes may be needed to ensure proper fusion and meet the required weld quality standards. Always refer to specific welding procedures and guidelines for accurate requirements.
How do you measure filet weld?
In a fillet weld, the leg and size are the same for the convex weld.
When API 650 tank roof nozzle reinforcement pad fouling with long seam weld of tank roof plate?
When an API 650 tank roof nozzle reinforcement pad is fouled with a long seam weld of the tank roof plate, it can lead to stress concentration and potential failure points due to the added heat-affected zone from the weld. This situation may compromise the integrity and functionality of the nozzle, potentially resulting in leaks or structural issues. Proper inspection and maintenance are crucial to identify and address any fouling or welding concerns to ensure the tank's safe operation. Additionally, adherence to welding standards and practices can help mitigate these risks.
How long can you weld underwater?
How long can you hold your breath?
Seam to seam length in horizental vessel?
The seam to seam length in a horizontal vessel refers to the distance measured from one seam to the opposite seam of the vessel along its circumference. It is an important measurement for determining the size and capacity of the vessel. This measurement is typically used in the fabrication and design of horizontal vessels such as tanks or pressure vessels.
What do you mean by seam welding where it is used?
seam welding is a process that produces a weld at the faying surfaces of two similar metals where its used depends on which metal you look to weld
What is the difference between seam and seamless pipe?
seam less pipes are having with out weld but produced by extension process it is costly than seam
Can you glue the plastic seam on a 2002 Saturn radiator?
If the seam is coming apart, use J B Weld between the parts and then if possible screw in 2 small self tapping screws through both parts at each end. This should pull the parts together, then finish off the top of the seam with J B Weld also.
How many weld passes does it take to fill a one deep weld seam?
The number of weld passes required to fill a one-deep weld seam typically depends on factors such as the joint configuration, material thickness, and welding technique used. Generally, for a single groove weld, it often takes one to three passes to achieve full penetration, but this can vary. In some cases, multiple passes may be needed to ensure proper fusion and meet the required weld quality standards. Always refer to specific welding procedures and guidelines for accurate requirements.
What do you use to glue seams in plexiglas?
You get plexiglass/perspex glue . -Weld On #3 , #4 or #16, depending on how tick you want the seam to be.
What is the cost to replace or weld up the heat shield seam of 1996 mercury villager?
That would depend entirely on where you take it to be repaired.
How do you measure filet weld?
In a fillet weld, the leg and size are the same for the convex weld.
When API 650 tank roof nozzle reinforcement pad fouling with long seam weld of tank roof plate?
When an API 650 tank roof nozzle reinforcement pad is fouled with a long seam weld of the tank roof plate, it can lead to stress concentration and potential failure points due to the added heat-affected zone from the weld. This situation may compromise the integrity and functionality of the nozzle, potentially resulting in leaks or structural issues. Proper inspection and maintenance are crucial to identify and address any fouling or welding concerns to ensure the tank's safe operation. Additionally, adherence to welding standards and practices can help mitigate these risks.
What is the purpose of the deck seam in a ship's construction?
The purpose of the deck seam in a ship's construction is to provide a watertight seal between the deck planks, preventing water from seeping into the ship's interior and ensuring the structural integrity of the vessel.
How long can you weld underwater?
How long can you hold your breath?
How do you examine the welds after the tests and check for weld quality?
You can have visual inspection, x-ray, ultrasound, magnetic testing. The seam can be ground, polished and tested with a stain marker. You can weld a test piece and have it submitted to destructive testing where it's pulled or bent until failure.
