The SK100 transistor is a general-purpose NPN transistor. An equivalent component can be the 2N3904 or BC547, which also serve similar functions in various electronic circuits. However, it's essential to check the specific electrical characteristics and ratings, such as current and voltage, to ensure compatibility in your application. Always consult the datasheets for precise comparisons.
It shows the Purification during the filtration of crude oil.
The SK series SLC (Signaling Line Circuit) loop on the Silent Knight 5829XL typically operates at a voltage of 24 volts DC. This voltage is used to power compatible devices connected to the loop, such as smoke detectors and pull stations. It's important to consult the specific installation manual or technical documentation for precise details and any variations based on configuration.
For example you have 24port switch capable of RxTx of 100mbps. then switching capacity is 24x100= 2400 mbps Rx plus 24x100=2400 mbps Tx . so a total of 4800mbps which is 4.8gbps.(non blocking architecture) Rgds, SK
#include //#include #define STU 3 #define SUB 3 void main() { int k,i; struct student { int rno; char name[20]; int marks[2]; int total; float avg; }sk; for(k=1;k
DefinitionAngioplasty is a procedure to open narrowed or blocked blood vessels that supply blood to the heart. These blood vessels are called the coronary arteries.A coronary artery stent is a small, metal mesh tube that expands inside a coronary artery. A stent is often placed after angioplasty. It helps prevent the artery from closing up again. A drug eluting stent has medicine in it that helps prevent closing of the artery.Alternative NamesDrug-eluting stents; PCI; Percutaneous coronary intervention; Balloon angioplasty; Coronary angioplasty; Coronary artery angioplasty; Cardiac angioplasty; PTCA; Percutaneous transluminal coronary angioplasty; Heart artery dilatationDescriptionBefore the angioplasty procedure begins, you will be given some pain medicine. You may also be given blood thinning medicines to keep a blood clot from forming.You will lie down on a padded table. Your doctor will make a small cut (incision) on your body, usually near the groin. Then your doctor will insert a catheter (flexible tube) through the incision into an artery. Sometimes the catheter will be placed in your arm or wrist. You will be awake during the procedure.The doctor uses live x-ray pictures to carefully guide the catheter up into your heart and arteries. Dye will be injected into your body to highlight blood flow through the arteries. This helps the doctors see any blockages in the blood vessels that lead to your heart.A guide wire is moved into and across the blockage. A balloon catheter is pushed over the guide wire and into the blockage. The balloon on the end is blown up (inflated). This opens the blocked vessel and restores proper blood flow to the heart.A stent (wire mesh tube) may then be placed in this blocked area. The stent is inserted along with the balloon catheter. It expands when the balloon is inflated. The stent is then left there to help keep the artery open.Why the Procedure Is PerformedArteries can become narrowed or blocked by deposits called plaque. Plaque is made up of fat and cholesterol that builds up on the inside of the artery walls. This condition is called atherosclerosis.Not every blockage can be treated with angioplasty. Some need coronary bypass(heart surgery).Angioplasty may be used to treat:Persistent chest pain (angina) that medicines do not controlBlockage of one or more coronary arteries that puts you at risk for a heart attackBlockage in a coronary artery during or after a heart attackRisksAngioplasty is generally safe, but ask your doctor about the possible complications. Risks of angioplasty and stent placement are:Allergic reaction to the x-ray dyeBleeding or clotting in the area where the catheter was insertedDamage to a heart valve or blood vesselHeart attackKidney failure (higher risk in people who already have kidney problems)Irregular heart beats (arrhythmias)Stroke (this is rare)Allergic reaction to the stent materialAllergic reaction to the drug used in a drug-eluting stentBlood clotClogging of the inside of the stent (in-stent restenosis)Before the ProcedureAngioplasty is often performed when you go to the hospital or emergency room for chest pain, or after a heart attack. If you are admitted to the hospital for angioplasty when it is not an emergency:Tell your doctor what drugs you are taking, even drugs or herbs you bought without a prescription.You will usually be asked not to drink or eat anything for 6 to 8 hours before the test.Take the drugs your doctor told you to take with a small sip of water.Tell your doctor if you are allergic to seafood, if you have had a bad reaction to contrast material or iodine in the past, if you are taking Viagra, or if you might be pregnant.After the ProcedureUsually, the average hospital stay is 2 days or less. Some people may not even have to stay overnight in the hospital.In general, people who have angioplasty are able to walk around within 6 hours after the procedure. Complete recovery takes a week or less. Keep the area where the catheter was inserted dry for 24 to 48 hours.Most people take aspirin and another medicine called clopidogrel (Plavix) after this procedure. These medicines are blood thinners, and they keep your blood from forming clots in your arteries and stent. A blood clot can lead to a heart attack. Take the medicines exactly as your doctor tells you. Do not stop taking them before talking with your doctor first.OutlookFor most people, angioplasty greatly improves blood flow through the coronary arteries and the heart. It may remove the need for coronary artery bypass surgery (CABG).Angioplasty does not cure the cause of the blockage in your arteries. Your arteries may become narrow again. Follow your heart-healthy diet, exercise, stop smoking (if you smoke), and reduce stress to help lower your chances of having a blocked artery again. Your health care provider may prescribe medicine to help lower your cholesterol.ReferencesBoden WE, O'rourke RA, Teo KK, et al. Optimal Medical Therapy with or without PCI for Stable Coronary Disease. N Engl J Med. 2007 Mar 26; [Epub ahead of print].Winslow RD, Sharma SK, Kim MC. Restenosis and drug-eluting stents. Mt Sinai J Med. 2005 Mar;72(2):81-9.
In the transistor, first letter denotes the material and the second letter denotes about the type of device. Hence here in sk100 transistor, first letter s denotes that it is a silicon transistor and second letter k denotes that it is a hall effect device.So, sk100 is a hall effect silicon transistor....
About 100 km.
100-300 or so
About $315
sk = skip
The distance between Wolseley, SK, and Regina, SK, is approximately 100 kilometers (62 miles) and takes about an hour to drive, depending on traffic and road conditions.
173 k
SK Brage ended in 2009.
Ljungskile SK was created in 1926.
Kållered SK was created in 1938.
SK Haugar was created in 1939.
Hilal SK was created in 1912.