answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

How do you calculate half load speed of induction motor if given full load peed?

To calculate the half load speed of an induction motor, you first need to understand that the synchronous speed remains constant regardless of the load. The full load speed is generally slightly less than the synchronous speed due to slip. To estimate the half load speed, you can use the slip at full load and apply it to the synchronous speed, recognizing that slip may change slightly at half load. However, for a rough estimate, you can assume half load speed is close to the full load speed, as the change in speed due to varying loads is minimal in induction motors.


For a half-wave rectifier there is current through the load for approximately what per- centage of the input cycle?

In a half-wave rectifier, current flows through the load for approximately 50% of the input cycle. This is because the rectifier only allows one half (positive or negative) of the AC waveform to pass through, effectively blocking the other half. As a result, current is present during the positive half-cycle of the input signal and absent during the negative half-cycle.


Difference betweeb Load balancing and Load sharing?

Load sharing is the ability to distribute outgoing traffic (or influence the flow of incoming traffic) over multiple paths. Load balancing is the ability to split the load toward the same destination (host or IP ) over multiple paths>>.In regard to CISCO Routers:Load sharing means one can split the traffic from a network to be transported by different routers (paths). That's exactly what Cisco does with MHSRP. The document on Configuring Multichassis Multilink PPP states that when it tells it to configure half of the hosts with one default gateway and the second half with the other. What happens, for instance, if the first half of the hosts are off? Will the traffic of the second half be transported by both routers?On the other hand, load balancing means distributing the traffic evenly and dynamically among different paths to avoid link congestion and saturation. This can be done in a packet-by-packet basis or per destination in a round-robin fashion. The packets sent by a host follow different paths to the same destination. All paths belong to all hosts. And this is not what MHSRP does.


A circuit diagram consisting of diode and transformer?

This is probably a half-wave rectifier.Rectifiers are used to convert AC to "DC". A half-wave rectifier can be constructed with a transformer and a diode connected between the positive terminal of transformer secondary and the load. This doesn't provide DC power to the load, but instead blocks the negative portions of the AC signal and only allows current to flow into the load while the AC voltage is positive. A capacitor is typically connected across the load to smooth out the voltage, making the input to the load more DC-like. The capacitor charges up when the AC voltage is positive and the diode is conducting, then discharges through the load when the diode is not conducting. This is still not DC power since there is a certain amount of ripple, or variation in the load voltage. Selection of the capacitor value is important to reduce ripple to an acceptable level. The transformer is simply used to change the AC voltage to whatever is desired.The half-wave rectifier is a very simple circuit. Other kinds rectifiers, for instance a full-wave rectifier, offer better performance.


Bear the load or bare the load?

Bear the load. Bare the load would be to uncover the load...

Related Questions

How do you fix half load in miscrits?

restart


Can I run my generator at half power if only drawing half load?

Yes, you can run your generator at half power if you're only drawing half load. Generators are designed to operate efficiently at various load levels, and running at half load can actually prolong the lifespan of the generator. However, ensure that the generator is still within its safe operating range to avoid any potential issues. Always consult the manufacturer's guidelines for optimal performance.


What force is required to lift a 8N load attached to a 2 pulley system?

The force required to lift an 8N load attached to a 2-pulley system is equal to half the load weight, considering ideal conditions. This means a force of 4N is required to lift the load because the pulleys distribute the load such that each side supports half of the load weight.


What is a better way to save water washing a full load or a half load?

always wait for a full load. it not only saves water but also electricity.


What is the ideal tire pressure for a 2000 accent?

its is mentioned in the glove box of the car. Full load its 33psi and with half load 30 psi


What is a half ton pickup?

A pickup truck that can safely carry a load of 1,000 pounds. This has nothing to do with towing capacity. It has to do only with load capacity.


What is 1 moveable pulley attached to a load?

A single moveable pulley attached to a load reduces the amount of force needed to lift the load by half. The pulley is free to move up and down, allowing for easier lifting and lowering of the load.


If you doubled the load resistor in a wheatstone bridge. the load current would not be half as much Why not?

Because by increasing the load resistance, the total circuit resistance is reduced. This means with less resistance, there is more current drawn from the source. Doubling the size of a load resistor increases the load current.


How much load can a 2003 gmc sonoma carry?

It is a half ton pickup ,correct?


How do you calculate the efficiency of half wave ractifier?

A: It all depends on the load and total capacitance. Without a load it would be 100% efficient minus the diode drops and wire IR resistance assuming a direct line to load.


Why when you open club penguin it comes up half a white screen and half reguler?

it is probobly because you have lag or something like that it will load eventually


How can I optimize the efficiency of my dishwasher when running it half-full?

To optimize the efficiency of your dishwasher when running it half-full, consider using the "half-load" or "eco" setting if available, use the appropriate amount of detergent, load dishes properly to allow for proper water circulation, and avoid pre-rinsing dishes to save water and energy.