0
What else can I help you with?
What is the applications opamp buffer circuit?
An opamp buffer circuit is one where the input signal is connected to the plus input, and the output is connected to the minus input. Within the performance limitations of the opamp, the output will track the input. The advantage of the buffer circuit is that is presents very little load impedance to the input signal, while providing a low impedance from the output to drive whatever circuitry is connected there.
Why input impedance of operational amplifier is infinite?
Input impedance (Zin) is assumed to be infinite to prevent any current flowing from the source supply into the amplifiers input circuitry. Infinite Input impedance is one of the Ideal Characteristics of the Op-Amp. With an assumption of Infinite Input impedance, there is no Loading on the preceeding stage to the Op-Amp (i.e. Supply.) or The Op-Amp under test does not draw any current from the I/p Supply to it's internal Circuitry.
Which is better high input impedance or low input impedance and why?
That depends on the output impedance. In electronic we use voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance. An input impedance is called also a load impedance or an external impedance. An output impedance is called also a source impedance or an internal impedance.
Compared to bipolars FETs have-a high input impedance b low input impedance c same input impedance?
FET s have very high input impedance when compared with Bipolar transistors.
Input impedance is greater than to load impedance?
In electronic gears we use voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
What is the applications opamp buffer circuit?
An opamp buffer circuit is one where the input signal is connected to the plus input, and the output is connected to the minus input. Within the performance limitations of the opamp, the output will track the input. The advantage of the buffer circuit is that is presents very little load impedance to the input signal, while providing a low impedance from the output to drive whatever circuitry is connected there.
Why the input resistance of opamp is high?
Because op amp consist differential amplifier and they posses high input impedance so that op-amp also posses high input impedance.
What is the input impedance of an ideal voltage op-amp?
To get all the voltage from a source to a target without loss you need voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
Why output impedence is high in opamp?
Output impedance in an op-amp is not high - it is low - input impendance is high, and this is because the input stage transistors have high gain.
What does 10 megohm input impedance mean?
10 megohms is the resistance through which 10 volts would push 10 microamps of current. Input impedance is the resistance seen by a signal source when connected to the input Often, this means there is a 10 megohm resistor in series with the input going to a virtual ground on an opamp circuit. 10 megohms is a common input impedance for a digital voltmeter.
Why input impedance of operational amplifier is infinite?
Input impedance (Zin) is assumed to be infinite to prevent any current flowing from the source supply into the amplifiers input circuitry. Infinite Input impedance is one of the Ideal Characteristics of the Op-Amp. With an assumption of Infinite Input impedance, there is no Loading on the preceeding stage to the Op-Amp (i.e. Supply.) or The Op-Amp under test does not draw any current from the I/p Supply to it's internal Circuitry.
Which is better high input impedance or low input impedance and why?
That depends on the output impedance. In electronic we use voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance. An input impedance is called also a load impedance or an external impedance. An output impedance is called also a source impedance or an internal impedance.
Why input resistance of voltage amplifier is infinity?
For the successful amplification of the input signal the opamp should have ideally infinite input impedance . It should act like a buffer amplifierBUFFER amplifier--------------------->1.input impedance infinity2.output impedance zerothe reason is thatAny signal source will have source impedancefor the signal not to get lost and dropped across source impedance we ideally insert infinite impedance in series with it which makes the whole drop across the infinite impedance but not across the sourcesimilarly at the output zero impedance is used where in no part of the signal should be left behind in the op amp as a drop
Compared to bipolars FETs have-a high input impedance b low input impedance c same input impedance?
FET s have very high input impedance when compared with Bipolar transistors.
In a multistage amplifier input impedance is high and output impedance is low justify the statement?
no. input impedance is low & output impedance is high
Input impedance is greater than to load impedance?
In electronic gears we use voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
Why input impedance is in parallel and output impedance is in series?
That is not the case. Scroll down to related links and look at "Measurement of input impedance and output impedance".
