A: RAIL is an English word to apply where we Americans call dc buss. Sometimes it is called the poke by our friends oversea. Anyhow that means that the circuit is probably swinging from bus to buss or rail to rail of poke to poke take your pick.
Generally, there will be a 12+ volt rail, a 5+ volt rail and often a 3+ volt rail.
power filter diagram
You probably mean "... where there should be a DC output ?",and the answer is "No. They don't work in reverse.".
you mean like show some sample output? Just put it in comments at the bottom. Run the program, and in the top left of the command prompt there is a button you can click. Select mark, highlight the output, then select copy. Paste it onto the end of the program.
The purpose of a rail is to keep someone from falling. You can hold onto the rail while walking up and down the stairs.
Generally, there will be a 12+ volt rail, a 5+ volt rail and often a 3+ volt rail.
LSA means that your amplifier will follow its specs also if you ask it to perform a large signal transition (ie fast output voltage change from rail to rail). In fact, bandwidth performances are given for small signal variation (a transition where output voltage variation is much smaller than rail to rail ).
Output voltage swing is defined as the maximum positive or negative peak output voltage that can be obtained without wave form clipping, when quiescent DC output voltage is zero. VOM is limited by the output impedance of the amplifier, the saturation voltage of the output transistors, and the power supply voltages. This is depicted in the figure below. This emitter follower structure cannot drive the output voltage to either rail. Rail-to-rail output op amps use a common emitter (bipolar) or common source (CMOS) output stage. With these structures, the output voltage swing is only limited by the saturation voltage (bipolar) or the on resistance (CMOS) of the output transistors, and the load being driven. Maximum and minimum output voltage is usually a design issue when dynamic range is lost if the op amp cannot drive to the rails. This is the case in single supply systems where the op amp is used to drive the input of an ADC, which is confiured for full scale input voltage between ground and the positive rail.
Output voltage swing is defined as the maximum positive or negative peak output voltage that can be obtained without wave form clipping, when quiescent DC output voltage is zero. VOM is limited by the output impedance of the amplifier, the saturation voltage of the output transistors, and the power supply voltages. This is depicted in the figure above. This emitter follower structure cannot drive the output voltage to either rail. Rail-to-rail output op amps use a common emitter (bipolar) or common source (CMOS) output stage. With these structures, the output voltage swing is only limited by the saturation voltage (bipolar) or the on resistance (CMOS) of the output transistors, and the load being driven.Maximum and minimum output voltage is usually a design issue when dynamic range is lost if the op amp cannot drive to the rails. This is the case in single supply systems where the op amp is used to drive the input of an ADC, which is configured for full scale input voltage between ground and the positive rail. Because newer products are focused on single supply operation, datasheets use the terminology VOH and VOL to specify the maximum and minimum output voltage.
It is slang for intercourse. To 'rail' a girl simply means to have sex with her.
The 12 volt rail on a power supply is a circuit that provides a steady flow of 12 volts to components like the CPU, GPU, and other high-powered devices in a computer. It is essential for powering these components efficiently and reliably. Variations in voltage output or instability on the 12 volt rail can impact the performance and stability of the connected hardware.
The name rail means a very delicat name of a very pretty smart girl
Actually you can not remove levels from rail simulator, which mean you have to pass the level.
Common Rail is a form of fuel injection used with gasoline and diesel engines
Rail is its own homonym Rail can also mean harshly, criticize Homonyms are words with different meanings but sound the same, some have the same spelling
Output is the end product: final product; the things produced.So the output of a bakery are the baked goods.
the output Value is the answer you get to a sum.For example:2x2= 4