0
What else can I help you with?
What effect if any does connecting an ammeter in series with a resistor in a circuit have on the current through resistor?
The Amp meter was design to allow current flow through the meter to measure with a minimal alteration to the original circuit. That is the ideal world, in reality the meter has some resistance and will lower the current flow. The multiple current setting on most meter will reduce the effects caused by the meter but you must be careful not to damage the meter by reading to high for the setting.
How is an ohmmeter connected to a circuit?
ANY METER needs some kind of current flow to operate. Internal in the meter there are batteries that provide current that when passed trough a resistor will develop voltage as a function of the current. the meter will read this current and display the resistor size to cause this current to flow.
What is the reason of reverse indication on in single phase kWH meter?
A kWh meter measures the flow of energy along the circuit that the meter is connected to. Normally power flows from the supply to the load, which is the conventional direction, but in some cases, for example if the load is replaced by a generator, power can flow the other way and in that case the meter indicates a backward, negative, flow of power.
When there is a break on the circuit what is the reading?
The typical answer is current is zero when there is a break in the circuit. It depends on the complexity of the circuit, there may be other paths for the current to flow, such that if there is a break in one part of the circuit, the rest of the circuit still has current flow (but a different value than designed). If you are reading voltage, and there is a break then that will change, also depending on the complexity. If it is a single loop, and you're reading voltage before the break, your voltmeter will read the same voltage as the voltage source, since there is no current flowing between any resistors between the meter and the source. If you're reading voltage after the break then the meter will read zero (0) volts.
What is closed path throuth which current can flow?
An electric circuit.
What is the purpose of a switch in an electric circuit and how does it function to control the flow of electricity?
The purpose of a switch in an electric circuit is to control the flow of electricity by opening or closing the circuit. When the switch is closed, it allows electricity to flow through the circuit, completing the path for the current. When the switch is open, it breaks the circuit, stopping the flow of electricity. This on/off functionality of the switch helps to control the flow of electricity in the circuit.
In a circuit the purpose of a switch is to?
In a circuit, the purpose of a switch is to control the current flow to the load by opening the circuit (off) or closing the circuit (on). When the circuit is open, the is no complete loop through which the current can flow. When the switch closes the circuit, it restores the loop, and thus allows the current to flow.
What does a switch in an electrical circuit do to control the flow of electricity?
A switch in an electrical circuit controls the flow of electricity by opening or closing the circuit, allowing or stopping the flow of electricity through the circuit.
How does a switch work in a circuit to control the flow of electricity?
A switch in a circuit works by opening or closing a pathway for electricity to flow. When the switch is closed, it completes the circuit and allows electricity to flow through. When the switch is open, it breaks the circuit and stops the flow of electricity. This control of the flow of electricity allows the switch to turn devices on and off in a circuit.
What is the purpose of a switch in an electric circuit?
A switch in an electric circuit is used to control the flow of electricity by opening or closing the circuit. It allows users to turn the circuit on or off, enabling them to control the flow of electricity to various components in the circuit.
Which is better to control a pneumatic cylinder- a meter-in flow control or a meter-out flow control?
When a pneumatic cylinder chamber is filled with pressurized air and the air-chamber on the other side of the piston is metered-out by a flow control, the movement or speed of the cylinder is more consistent than to meter-in the pressurized air.
What does a flow meter control?
A flow meter is a device that measures the energy flow of either a liquid or a gas. Like if you have nitrous oxide in a tank and you want to know how much is left after you use some, a flow meter would tell you.
What is the purposed of resistance in the circuit?
Resistance is generally used to control the flow of amount of current in the circuit.
Why meter in and meter out is not in pneumatic system?
Meter in and meter out are terms commonly used in hydraulic systems to control the flow rate of fluid. In pneumatic systems, flow control valves such as needle valves or flow restrictors are used to regulate the speed of the air flow. These components are designed specifically for pneumatic applications due to the differences in fluid properties and system requirements between pneumatic and hydraulic systems.
How a fuse controls the flow of electric current in a circuit?
A fuse does not control the flow in a circuit, it limits the current in a circuit. If the load in a circuit shorts out the fuse link melts and opens the circuit and stops the current flow and prevents the wires feeding the circuit from melting and catching fire. resist
How do switches affect open and closed circuits?
Switches control the flow of electric current in a circuit. In an open circuit, the switch is off, interrupting the flow of current. When the switch is closed in a closed circuit, it allows the current to flow continuously through the circuit.
How does bleed off flow control differ from meter in and meter out?
meter in: regulates the speed of the actuator by controling the amount of fluid entering in to the actuator. meter out: regulates the speed of the actuator by controling the amount of fluid leaving the actuator. bleed off: regulates the speed of the actuator by metering a part of the pump flow to the tank. Prof. Mahesh Chopade MIT College of Engineering, Pune
