0
Regulation has to do with keeping the voltage at a desired value. This is often put in a per unit value, which you can think of as a percent of nominal. So if the desired voltage is 34.5kV, and the actual voltage is 33.8kV, the voltage is .98 per unit. There are regional and national rules on how low or high voltage can be. If the voltage strayes from this, it must be regulated back to an acceptable value.
What else can I help you with?
How the voltage regulation in 33kv line?
It does not depend on the line. The regulation is the percentage change in voltage caused by applying the full load current, and that depends on the transformer supplying the line. A value of 5% would be typical.
Will low pass filter works as transmission line?
No, but transmission line act as a lpf
Who uses pole and transmission line hardware?
Pole and transmission line hardware is purchased by cable television and utility companies
Why phases in transmission line are transposed?
Image result for Why phases in transmission line are transposed?Transposition is the periodic swapping of positions of the conductors of a transmission line, in order to reduce crosstalk and otherwise improve transmission. ... Transposition also equalizes their impedance relative to the ground, thus avoiding one-sided loads in three-phase electric power systems.
Calculations on input impedance of a transmission lines?
I assume you are wanting to know about balancing networks to a transmission line? If this is the case, you really need to get a book on networks and filters. The physical makup of the transmission line will impact this calculation. The basic idea is you want to match the impedance at the input (looking out of the transmission line) to the same impedance as the transmission line (say 50 or 75 ohms for typical coax), and the output impedance (looking out of the transmission line) to the same as well. This will result in maximum power transfer, minimum power reflection. If you want to know how to make a balancing filter to a transmission line, then you need to design the filter according to your requirements - chebyshev, minimum ripple, wide band, narrow band, etc; You may need to use transformers to isolate the transmission line from your power circuitry, and use this as a matching network. You could also use transistors to accomplish similar things (less isolation, though), depending on what you're trying to do.
Define voltage regulation and efficiency of a short transmission line?
Voltage Regulationvoltage regulation of a line is defined as the change in voltage at the receiving end when full load at a given power factor is removed, the voltage at the sending end being kept constant. it is expressed as a fraction or a percentage of the receiving end voltage at full load. it can be written as, Per unit regulation = Vrnl - Vrfl / VrflPercent regulation = (Vrnl -Vrfl / Vrfl) * 100Efficiency of a Short Transmission LineIt is the ratio of the Power Output of the line to the Power Input of the line.
What is the voltage regulation of medium transmission line?
Voltage regulation is just the percentage change in voltage at the receiving/sending end of the transmission line from no load to full load. It is given by ((Vnl-Vfl)/(Vnl)) X 100%. Typically Voltage at receiving end is known to us and for the sending end Vnl is given by Vs/A. Where A is given by the ABCD parameters of the transmission line and Vs = AVr + BIr.
What is line regulation?
Line regulation is a measure of the ability of the power supply to maintain its output voltage given changes in the input line voltage. Line regulation is expressed as percent of change in the output voltage relative to the change in the input line voltage.
What is line in line regulation?
Line refers to the a.c. supply line. Line regulation is the change in output of a device, usually a power supply, which is due to variations in the voltage of the a.c. supply.
How do you change transmission line?
how to fix a transmission without taking it a part how to fix a transmission line
Do you get DC current directly from the transmission line?
Only if it is a DC transmission line.
Is there one coolant line or two for the transmission on a 98 Mercury?
If this vehicle has a transmission cooler then it will have one line to the cooler then another for the return line to the transmission.
Line regulation and load regulation of zener diode?
Line regulation defines as the output voltage of the zener to remain constant under input line variation. Load regulations defined as the load increases or decreases the zener will control this variation by keeping the voltage constant.
How the voltage regulation in 33kv line?
It does not depend on the line. The regulation is the percentage change in voltage caused by applying the full load current, and that depends on the transformer supplying the line. A value of 5% would be typical.
Will low pass filter works as transmission line?
No, but transmission line act as a lpf
In a regulation volleyball game the sever must severer behind what line?
The end line
What is A in the nominal pi model of transmission line?
balanced pi model for a long transmission line.
