0
What else can I help you with?
What feedback does a close loop servo mechanism uses?
kidney
What is definition of open loop transfer function?
According to 'Modern Control Engineering' written by Katsuhiko Ogata, the ratio fo the feedback signal, H(s)C(s)to the actuating error signal (R(s)-B(s)) is called the open-loop transfer function. Here, H(s) is the transfer function of the feedback signal detector, C(s) is the output signal and R(s) is the setpoint signal.
What is the range of a safety valve settings for a boiler operation at 1000 psi?
There is no range on a safety valve. It lifts and relieves at whatever it`s setpoint is. As for the setpoint, it would be just above the maximum working pressure/temperature of the water side of the boiler as stated on the National Board Tag of the vessel.
What is loop logic structure?
I believe it is: Loop condition Loop actions And how the loop breaks
What is a PID controller?
A proportional-integral-derivative controller(PID controller) is a generic control loop feedback mechanism (controller) widely used in industrial control systems. A PID controller attempts to correct the error between a measured process variable and a desired setpoint by calculating and then outputting a corrective action that can adjust the process accordingly and rapidly, to keep the error minimal.
Open loop and close loop system in injection moluld machine?
loop checking is perform before cable termination..the difference between a close loop and open loop is,tha close loop has a feedback while the open loop has not.
What is the type of homeostatic mechanism that reduces any changes in the value of a variable or keeps a variable close to a particular pre-established setpoint?
Negative feedback is the homeostatic mechanism that reduces any changes in the value of a variable or keeps a variable close to a pre-established setpoint. When the system detects a deviation from the setpoint, it initiates actions to bring the variable back to its desired level.
What is the word for the weight at which your body naturally tends to stabilize?
setpoint.
Is voltage stablizer open loop or close loop?
Closed
Is the gain same for the same system in open loop and close loop?
no.
What is difference in close loop and an open-loop control?
no difference that's the difference
How are negtive feedback different from positive feedback?
some feedback r insulting or inappropriate. it depend on how u sort the question. Question is on feed back system in control system. In a control system generally there is a setpoint to be achieved. Control system aims to achieve the setpoint. However due to inherent reasons, the actual keeps hovering around the setpoint. A good control system keeps the setpoint very close to the setpoint. Control system must know the actual value to make adjustment to achieve the setpoint. Actual value is fed back to the control system. This feed back is referred as negative or positive feedback. The feed back tells the control system that the actual value is lower or higher compared to set point. This is known as negative or positive feedback.
Reason use an op amp in a closed loop control system?
Differential Amplifier or Summing Amplifier are usually used in a closed loop control system. The error signal will be the DIFFERENCE between the setpoint value and feedback value for Differential Amplifier. Whereas for Summing Amplifier, the error signal will be the difference between the setpoint value and feedback value only if one of the value is inverted in polarity. Another reason Op Amp is used: amplify the error signal as error signals are usually very small. Hope this helps.
What actors and actresses appeared in Close the Loop - 2013?
The cast of Close the Loop - 2013 includes: Brian Miskell as Paul Diana Stahl Sanford Wilson as Mark
What is the definition of close the loop in recycling?
The term "close the loop" is a three part process: 1) recycle our waste, 2) make something new out of it, 3) buy recycled.
What feedback does a close loop servo mechanism uses?
kidney
What is the difference between regulatory control system and servo system?
Well, sweetheart, a regulatory control system is like a strict parent that keeps things in line by maintaining a set value, while a servo system is more like a personal assistant that adjusts based on feedback to reach a desired position or speed. So basically, one plays by the rules, while the other is more flexible and adaptive. Hope that clears things up for you, pumpkin!
