0
What else can I help you with?
What is the fuel ratio?
fuel mixture for homelite chain saw
How Two Stroke Single cylinder Petrol Engine Working?
As the piston rises it compresses the fuel-air mixture and simultaneously sucks fuel and air into the crankcase. A little bit after top dead center, the spark plug fires the compressed mixture forcing the piston back down. As the piston travels down, it uncovers the exhaust and intake ports. The fuel-air mixture in the crank case is forced into the cylinder and blows most of the exhaust gas out by the time the piston starts upwards again and covers the exhaust port. The piston continues upwards to compress the fuel-air mixture and the next cycle starts. There is a very nice animation at the link, below.
Can you name and describe the four strokes that make up one full cycle of a 4-stroke engine?
The Otto cycle, know as the four stroke cycle is as follows.InductionCompressionPowerExhaustThis is a simplified explanation of a petrol engine, the basic details are correct. Most are also relevant to a CI engine. It is not meant to be a definitive answer and is only a description for the basic operation.Induction:The inlet valve opens and the piston moves down the cylinder causing a partial vacuum and drawing an air/fuel mixture into the cylinder through the inlet manifold.Compression:The inlet valve closes and the piston moves up the cylinder compressing the air/fuel mixture. The compression ratios vary.Power:Near the top of the compression stroke a spark is induced and the air/fuel mixture is ignited. This causes the gasses to expand rapidly and forces the piston down the cylinder.Exhaust:The exhaust valve opens and the piston moves up the cylinder expelling the burnt gasses out through the exhaust manifold. The exhaust valve closes and the cycle starts again.intake: In this stroke air (and in non-fuel-injected engines gasoline) is drawn in.compression: In this stroke air (and in non-fuel-injected engines gasoline) is compressed (just before the end of this stroke in fuel-injected engines the gasoline is injected, then a spark ignites the fuel/air mixture).expansion: in this stroke the burning fuel/air mixture pushes against the piston, doing work.exhaust: in this stroke the burnt fuel/air mixture is pushed from the cylinder to make room for a fresh charge on the next intake stroke.Intake, compression, power, exhaust.The first stroke down takes the air/fuel mixture in thus intake, then as the cylinder rotates up, the mixture compresses. The fuel is ignited and the power stroke starts down and as the cylinder goes back up it is the exhaust phase where it expels the burnt fuel and then starts the first stroke again
How does a nitro engine work?
The operation of a nitro engine is similar to a normal gas/diesel engine, where a fuel mixture is ignited, and the energy drives cylinders back and forth in a cycle, all the while keeping an element hot so that the fuel stays ignited. The only difference is that a nitro mixture is more complicated, so a hole has to be bored into the engine so the mixture can keep flowing in a certain way.
Why si engines are quantity governed engines?
SI (Spark Ignition) engines are considered quantity governed because their power output and performance are primarily controlled by the amount of air-fuel mixture entering the combustion chamber. The throttle valve regulates this mixture, affecting engine speed and torque. The engine's operational efficiency is linked to the precise control of fuel and air, making it essential to manage these quantities to optimize performance and emissions. Thus, the engine's behavior is largely dictated by the quantity of fuel and air rather than the mixture's quality or combustion characteristics.
How do you reset a fuel pump switch on a 1993 Ford Tempo?
how do you reset a fuel pump switch on a 1993 ford tempo
Where is the fuel filter located on a 1990 Ford Tempo?
It is under the hood, on the passangers side, right above the wheel well.
Where is the fuel pump on a 1989 Ford Tempo?
Fuel injected? In the fuel tank
Where is the fuel pump located on a 1993 Ford Tempo?
the fule pump is in the gas tank in the 1993 ford tempo
Where do you check fuel pressure on a 1990 Ford Tempo?
To check the fuel pressure on a 1990 Ford Tempo, locate the fuel rail on the engine, which is typically situated on top of the intake manifold. There should be a Schrader valve on the fuel rail; you can use a fuel pressure gauge to check the pressure by attaching it to this valve. Make sure to relieve the fuel system pressure before connecting the gauge to avoid any spills or injuries. Always follow safety precautions, as fuel can be hazardous.
Is a 92 Ford Tempo fuel injected?
yes it is
Where is the Fuel Injection switch for a 1990 Ford Tempo?
the fuel inj switch is located inside the ecm "the cars computer"need to check with a noid light to see if injectoris pulsing.
How do you replace a fuel pump in a 1988 Ford Tempo?
defective fuel pump
Where is the fuel pump on 1991 Ford Tempo?
fuel pump is in the gas tank.!!
How do you replace the fuel pressure regulator on a 1990 Ford Tempo?
To replace the fuel pressure regulator on a 1990 Ford Tempo, first, relieve the fuel system pressure by removing the fuel pump fuse and running the engine until it stalls. Disconnect the negative battery cable, then remove the fuel lines and electrical connector from the regulator. Unbolt the regulator from the fuel rail, replace it with the new one, and reassemble the fuel lines and electrical connections. Finally, reconnect the battery, reinstall the fuse, and start the engine to check for leaks.
Where is the fuel pump located in a 1994 ford tempo?
The fuel pump is inside the fuel tank.
Where is the fuel pump located on a 1992 Ford Tempo?
in the tank
