0
What else can I help you with?
What is the peak value of the input to a half wave rectifier if the half wave rectifier is 10V?
In this case, the peak voltage, which is half the peak to peak voltage, is 100 volts. Additionally, the half-wave rectifier will only provide an output for half the input cycle. In the case of a full wave rectifier, the RMS output voltage would be about 0.707 times the value of the peak voltage (100 volts), which would be about 70.7 volts. But with the output operating only half the time (because of the half wave rectification), the average output voltage will be half the 70.7 volts, or about 35.35 volts RMS.
If a single phase 240 Volt ac is applied to a full wave bridge rectifier. what will be the resultant dc voltage?
A: the rms value will be169 volts add a capacitor and no load 240 volts and the average will be 153 volts
What is voltage regulation of a rectifier?
A: actually a full wave rectifier does not regulate. It will however follow the input minus diodes voltage drops. depending on current it is assumed to be .6 to .7 volts for silicon diodes.
What should be the secondary voltage of a transformer needed in a rectifier circuit if the required DC voltage is 6 volts using a?
A little more than 6 volts RMS, or 17 volts peak to peak (can get -6 and +6 voltage this way using a full wave rectifier). The voltage will depend strongly on your design - are you using circuitry that clamps the output voltage to a specific value (you should!). If you are doing this, I would find the cheapest transformer that meets the current capacity you need that has an output near the 6 volts you want.
Rms value defination?
Because alternating current (AC) voltage varies over time, to the positive and negative, an actual AC voltage measurement will not be the same as a DC voltage measurement. For example: 5 volts DC is 5 volts constantly, viewed over time. The average voltage is 5 volts. 5 volts AC (from zero to peak) is not actually 5 volts constantly, but varies between 5 volts and 0 volts over time. The average voltage will not be 5 volts. Using RMS AC values is designed to make AC and DC measurements equivalent, for example 5 volts DC and 5 volts RMS AC are almost identical.
What is the peak value of the input to a half wave rectifier if the half wave rectifier is 10V?
In this case, the peak voltage, which is half the peak to peak voltage, is 100 volts. Additionally, the half-wave rectifier will only provide an output for half the input cycle. In the case of a full wave rectifier, the RMS output voltage would be about 0.707 times the value of the peak voltage (100 volts), which would be about 70.7 volts. But with the output operating only half the time (because of the half wave rectification), the average output voltage will be half the 70.7 volts, or about 35.35 volts RMS.
Formula for peak inverse voltage?
piv:the maximum value of reverse voltage across a diode that occurs at the peak of the input cycle when the diode is reversed-biased.
If a single phase 240 Volt ac is applied to a full wave bridge rectifier. what will be the resultant dc voltage?
A: the rms value will be169 volts add a capacitor and no load 240 volts and the average will be 153 volts
What is voltage regulation of a rectifier?
A: actually a full wave rectifier does not regulate. It will however follow the input minus diodes voltage drops. depending on current it is assumed to be .6 to .7 volts for silicon diodes.
What should be the secondary voltage of a transformer needed in a rectifier circuit if the required DC voltage is 6 volts using a?
A little more than 6 volts RMS, or 17 volts peak to peak (can get -6 and +6 voltage this way using a full wave rectifier). The voltage will depend strongly on your design - are you using circuitry that clamps the output voltage to a specific value (you should!). If you are doing this, I would find the cheapest transformer that meets the current capacity you need that has an output near the 6 volts you want.
What is a regulator on a motorcycle?
A regulator is referring to a regulator rectifier which converts the ac voltage put out by the stator to dc voltage and regulates it to a consistent voltage usually 12-14 volts dc.
What is the average amount of voltage in the average Australian home?
1000000 volts
How can you 120 volts AC to 5 volts DC?
By a DC power supply that runs at 230 volts AC. Basically, you need a full wave rectifier (4 diodes) to convert AC into all positive voltage. Then you need capacitors to smooth out the ripple and then various resistors to reduce the voltage.
Is 30 volts of AC voltage the same as 30 volts of DC voltage?
30VAC is not equal and will never be equal to 30VDC. If you rectify 30v ac to DC you will get a voltage lower than 30v because there would be a voltage drop across the rectifier=diode,capacitor,resistor and transistors or thyristor, depending on the make of the rectifier.AnswerAs the questioner makes no mention using a rectifier, yes, 30 V a.c. is exactly equivalent to 30 V d.c. This is because a.c. voltages are root-mean-square values (unless otherwise stated) which, by definition, correspond to d.c. voltages.
How much voltage does an alternator put out?
Automotive Alternator Output VoltagesWith a properly operating alternator, AND electrical system, a voltage output range of 13.5 Volts to 16 Volts is considered acceptable.Just the alternator puts out around 120 vac, but most newer alternators include a built in rectifier that limits voltage output to between 13.5 and 15.5 volts DC depending on speed.
What is 1N4OO1silicon diodes?
It's 1N4001 Maximum reverse voltage 50 volts, 1 amp The last digit indicates the voltage. To replace a 1N4001, you could safely use any of the diodes in that series. 1N4001 = 50 volts 1N4002 = 100 volts 1N4003 = 200 volts 1N4004 = 400 volts 1N4005 = 600 volts 1N4006 = 800 volts 1N4007 = 1000 volts The 1N4000 series diodes are rectifier diodes. They're used for converting AC voltage into DC voltage. And frankly, I can't think of a reason why I'd choose the 1N4001 when the more-versatile (as in you can use it in more places) 1N4003 is the same price.
What is an average voltage?
In different electric and electronic devices, voltages are used in the range of perhaps 0.5 volts to 5 million volts. So the average is somewhere in the neighborhood of 2,500,000.25 volts.
