0
What else can I help you with?
When installing double wall flue pipe?
What is the clearance around a zero clearance fireplace flue pipe inside of the surround that you build assuming it is double wall or type L since there is a gas log in the old surround.
What is a wall to wall supporting beam called?
joist
Do you put the vapor barrier of insulation on the inside or outside for an exterior wall application?
Inside, after the insullation, and wiring
How close can a wood support be to a gas fireplace wall chimney?
Depends on the rating and installation information from the maker. Some are "zero clearance" appliances- they can be attached directly to wood studs.
Can a leaky concrete wall be repaired from inside the basement?
Concrete walls will usually leak from wall cracks or from the joint where the floor and wall meet. Both can be fixed from inside by installing a sub-floor drainage system and a good wall sealer that will expand and contract along with the foundation. The Only Product that is FLOOD TESTED and PROVEN to work inside is ArmorGuard Basement Coatings, ArmroGuard Coatings are Non_Toxic, Odorless and Permanent, This Will SOLVE YOUR PROBLEMS GUARANTEED. Go to www.ecosmartepoxysystems.com for more information
What is fireplace reflector?
A fireplace reflector is a metal shield that is placed at the back of a fireplace to reflect heat back into the room. It helps increase the efficiency of the fireplace by preventing heat loss through the back wall and directing it back into the living space.
How do you turn on a gas fireplace using the wall key?
To turn on a gas fireplace using the wall key, insert the key into the keyhole on the wall near the fireplace. Turn the key clockwise to open the gas valve and allow gas to flow to the fireplace. Then, use the fireplace's ignition switch or button to ignite the gas and start the fire.
What purpose do firebacks provide?
The primary purpose of a fireback, a metal plate attached to the back of a fireplace, is to hold heat from the fire and reflect the heat back into the room. A secondary purpose of the fireback is to protect the back wall of the fireplace from damage due to repeated exposure to fire.
How do you turn on a gas fireplace using a wall switch?
To turn on a gas fireplace using a wall switch, first locate the switch on the wall near the fireplace. Flip the switch to the "on" position. Then, press and hold the ignition button on the fireplace until the pilot light ignites. Finally, release the button and adjust the flame height as needed using the wall switch.
How far should a mantle stick out from the wall above a fireplace?
A mantle should typically stick out about 6-8 inches from the wall above a fireplace.
What is the meaning of the word fireback?
The meaning of the work "fireback" can mean two things. One is the back wall of a fireplace, and a metal plate covering a wall. These are the only two definitions for the word "fireback."
What are the cons of using an electric wall fireplace?
The cost of an electric wall fireplace can be hefty, as well as the addition cost to use the unit. The electric wall fireplace can give off an illusion of being a "safe" alternative to a regular fireplace, and as a result, the user may leave it unattended. This poses a greater fire hazard risk.
Meaning of fireplace?
A niche in a wall to have a warming fire.
When installing double wall flue pipe?
What is the clearance around a zero clearance fireplace flue pipe inside of the surround that you build assuming it is double wall or type L since there is a gas log in the old surround.
What is the picture that Patch puts on the wall above the fireplace in his study in Proxy by Jane White?
Patch put a framed print of "The Scapegoat" by Holman-Hunt on the wall above the fireplace.
What was the front wall of a trench called?
the front wall was called a parapet the back wall was a parados
How do I operate the gas fireplace wall switch?
To operate the gas fireplace wall switch, simply flip the switch to the "on" position to ignite the fireplace and adjust the flame height as needed. Make sure to follow the manufacturer's instructions for proper use and maintenance.
