0
What else can I help you with?
Why does a static condenser differ from synchronous condenser?
Unlike a static condenser (capacitor bank), the value of reactive power from a synchronous condenser can be continuously adjusted. A synchronous condenser also has other advantages over static condensers such as: - not being affecting by harmonics (some harmonics can even be absorbed by a synch condenser) - producing no switching transients
Why is a condenser called a condenser?
The reason why it is called a barometric condenser is because it makes contact and it is a long vertical pipe into which it condensates and cools the liquid flow to accomplish the removal of pressure. It is also stated that when the pump is used the system is called a low level barometric condenser.
What is the role of a condenser system?
There are several roles of a condenser system depending on what is using it. In a microscope, a condenser system helps gather and focus light for a clearer view. In an air conditioner a condenser system cools heated gas so it can be used again.
Why is a liebig condenser connected to a tap?
To keep the Liebig condenser cool so it can condense the vapour
Why does the largest heat loss occur in a condenser in regard to steam?
heat losses in condenser in percentage
What TD is used to determine the condenser performance of a water cooled condenser?
The approach temperature difference (ATD) is used to determine the condenser performance of a water-cooled condenser. It is the temperature difference between the refrigerant condensing temperature and the cooling water inlet temperature. A lower ATD indicates better performance and efficiency of the condenser.
Can the condenser approach be a negative number?
Yes, the condenser approach, which refers to the temperature difference between the condensing fluid and the ambient environment, can be a negative number. This occurs when the condensing fluid is cooler than the surrounding environment, indicating that heat is being absorbed from the surroundings rather than released. Such a scenario can impact the efficiency of heat exchangers and condenser systems, potentially leading to operational challenges.
What is a condenser named after a scientist?
Liebig condenser, Vigreaux column, Snyder column, West condenser, Allihn condenser, Graham condenser, Dimroth condenser, Friedrichs condenser. There are no shortage of these!
Where is the condenser on a 2001 Chevrolet Malibu?
Which condenser are you asking about? There are a couple things that are called a condenser.
What is next to grill radiator or condenser?
Condenser
Where to find step by step instructions to replace the air conditioning condenser in a 2005 gmc canyon?
Drain the cooling system.Remove the radiator.Recover the refrigerant.Remove the receiver dryer.Remove the condenser inlet hose bolt.Remove the condenser inlet hose.Remove the condenser outlet hose bolt.Remove the condenser outlet hose.Remove the condenser from mounts on the radiator.Remove the condenser...........................
What are the symptoms of an cooled Condenser when the air leaving the condenser is hitting a barrier and recirculating?
What are the symptoms of an cooled Condenser when the air leaving the condenser is hitting a barrier and recirculating?
When was the Liebig condenser invented?
when the Liebig condenser was invented
How do you clean air conditioner condenser on a ford f250?
The inside of the air conditioner condenser can be cleaned by removing the hoses and running water through the condenser. Run water through the condenser until the water exiting the condenser is clear.
What is chiller approach temperature?
Evaporator Approach is the difference between the evaporating refrigerant temperature - measured at the well in the evaporator -and leaving chilled water temperature.Take all readings with the water cooled chiller at full load.Condenser Approach is the difference between the liquid refrigerant temperature - as measured on the liquid line - and leaving condenser water temperature.
What is a chiller approach temperature?
Evaporator Approach is the difference between the evaporating refrigerant temperature - measured at the well in the evaporator -and leaving chilled water temperature.Take all readings with the water cooled chiller at full load.Condenser Approach is the difference between the liquid refrigerant temperature - as measured on the liquid line - and leaving condenser water temperature.
What makes a condenser freezes over?
Possible blockage in the condenser.
