0
What else can I help you with?
What do you mesure the answer of Ohm's law in?
Ohm's law can be used to find the current, voltage or resistance in a electrical circuit. The formula is V=IR where 'V' is the Voltage measured in Volts (V), 'I' is the current measured in Amperes (A) And 'R' is the resistance, measured in Ohms (Ω)
What are Ohms Law and the Power Law?
Ohms Law is used for the measurement of resistance. You can find the resistance in a series circuit using this equation; amps=volts/resistance or volts=amps x resistance.The Power Law is used to find the wattage in the circuit. You can find the amount of watts using this equation: watts=volts x amps.CommentOhm's Law has nothing whatsoever to do with either resistance or power.The equation, R = E/I, is derived from the definition of the ohm, and not from Ohm's Law.Ohm's Law simply describes a linear relationship between the potential difference across a conductor and the current through it. It does NOT describe the relationship between potential difference, current, and resistance.
What is common to both thevenin and norton theorem?
To solve any D.C. circuit by using Thevenin Theorem,First of all load resistance RL is disconnected from the circuit and open circuit voltage across the circuit is calculated (known as Thevenin equivalent voltage)Secondly, the battery is removed by leaving behind its internal resistance. Now we calculate equivqlent resistance of the circuit ( called Thevenin equivalent resistance).Now we connect Thevenin Voltage in series with Equivalent resistance of the circuit and now connect load resistance across this circuit to calculate current flowing through the load resistance.Whereas in the case of using Norton theorem, we again remove the load resistance if any, and then short circuit these open terminals and calculate short circuit current Isc.Second step is same as in Thevenin theorem i.e. remove all sources of emf by replacing their internal resistances and calculate equivqalent resistance of the circuit.Lastly, join short circuit current source in parallel with equivalent resistance of the circuit. Now, we can calculate votage across the resistance which was connected in parallel with Isc.So, by knowing the open circuit voltage, we can calculate current flowing the resistance and on the other hand , by knowing the short curcuit current , we can calculate voltage across the resistance.
What is the wheat stone bridge principle?
It is an circuit that is used to find the value of the resistances. The main principle behind it is the balancing an circuit by means of varying an resistance on connected to an arm of the circuit.When the resistance become equal to the variable resistance no current flows thus we can find the value of the resistance.
When a 12v battery is connected across an unknown resistor 2.5mA current flows in the circuit find the resistance of the resistor?
Using ohm's law v=IR but we need to find the Resistance so, in place of v write r R=V/I
How do you find resistance in a circuit?
That entirely depends on whether the resistances are in series or in parallel with each other. Ohm's law states that I=V/R. i.e. current = voltage/resistance. If you know the current and voltage you can find the resistance. You can use algebra to rearrange the formula for R and get that R= V/I. Resistance = voltage/current.
What is the current in a circuit that has a resistance of 30 ohms and a power of 2 watts?
To find the current in the circuit, you can use the formula: Power = Current^2 * Resistance. Given the values, you can rearrange the formula to solve for current: Current = sqrt(Power / Resistance). Plugging in the values, you get Current = sqrt(2 / 30) which simplifies to approximately 0.27 amperes.
How to calculate the current in a circuit?
To calculate the current in a circuit, you can use Ohm's Law, which states that current (I) equals voltage (V) divided by resistance (R). The formula is I V/R. Simply plug in the values for voltage and resistance to find the current flowing through the circuit.
What is the formula to find out the total resistace of the series parellel circuit?
i think first one should find out the series resistance that is R1+R2+R3 and after that parellel resistance that is 1/R1+1/R2+1/R3 and after that add the series resistance and parellel resistance to get the total resistance
How do you find out the resistance on a circuit?
E = I* R is Ohm's Law. Where: E = voltage I = current R = resistance Using simple algebra yields: R = E / I
How do you find resistance when you have current and resistance total?
If you are looking for the resistance of each resistor in either a series circuit or a parallel circuit you must measure the current I and the voltage V for each resistor. Then calculate its resistance using Ohms Law R = V / I where I = current (Amps), V = voltage (Volts) and R= resistance (Ohms).
What is the net resistance of the circuit connected to the battery in the figure?
To find the net resistance of the circuit connected to the battery in the figure, you need to calculate the total resistance by adding up the individual resistances in the circuit.
What is meant by calculate the equivalent resistance of the circuit from the measured potential difference across the battery and the current through the battery is there a formula for this?
In a complex circuit with various elements (resistors, capacitors etc.) and one battery, the various circut elements contribute to draw a certain amount of current "I"from the battery at some terminal voltage "V". The "equivalent" resistance of the various circuit elements is that resistance "R" which will draw the same current , at the same terminal voltage, as the complex circuit. So to find "R" you simply imagine replacing the complex circuit with "R" by attaching "R" across the terminals of the battery and use Ohms law to find "R" , demanding "I" and "V" are the same. So then R = V/I.
When using a 60.0 W light bulb in a household circuit what is the resistance?
To calculate the resistance of the 60.0 W light bulb, you need to know the voltage of the household circuit. Using the formula P = V^2 / R (where P is power in watts, V is voltage in volts, and R is resistance in ohms), you can rearrange to solve for resistance: R = V^2 / P. Substitute the given power (60.0 W) and the voltage of your household circuit to find the resistance.
What is the equivalent resistance through the entire circuit?
The equivalent resistance is the overall effect all of the resistances in a circuit has. Put another way, it is the value a single resistor in a circuit would have to be in order to have the same effect as all of the resistors resistors combined in a given circuit.
How many test leads are needed to find resistance?
The test equipment needs two test leads to find the resistance in a circuit.
How do you find the resistance of a series circuit with n identical resistors?
The total resistance of resistors in series is simply the sum of the resistance values of those resistors. If the resistors are identical, then you can multiply the resistance of one of them by the number of resistors in the circuit.
