0
What else can I help you with?
What is the russian ''gost'' standard equivalent of astm a615 gr 60 reinforced iron bar-rebar?
The Russian GOST standard equivalent to ASTM A615 Grade 60 reinforced steel rebar is GOST 5781-82, specifically the steel grade A500C. This standard specifies the requirements for hot-rolled steel bars used in concrete reinforcement, similar to the properties defined in ASTM A615. The GOST rebar typically has a yield strength of 500 MPa, aligning closely with the Grade 60 designation in the ASTM standard.
What is the upper limit of ultimate tensile strength of ASTM-615A bars above which rejection is recommended?
Why would you reject material that overperformed its tensile-strength specs? The standard for Concrete Reinforcement rebar,astm-615a Grade 60 (60,000 PSI minimum yield strength)
What is the full name of the blackhawk helicopter?
I believe it is called the UH 60 Black Hawk
What hardness should SAE 1010 cold rolled steel be?
According to the ASME, SAE1010 {ASTM A179, ASME SA179} cold rolled steel (cold drawn) should have a Rockwell hardness of 60 RB. Hot rolled it is reduced to 55 RB. *(Brinell hardness, 105; Knoop hardness, 123; or Vickers hardness, 108)
Difference between astm d-226 and d-4869?
Different types of asphalt felt have different weights. Here are some data on the weight of felt types per 100 square feet: Weight per 100 square feet: Unrated (non-ASTM) #15 felt: 7.6 to 8.8 lbs. ASTM D 4869 #15 felt: 8.0 to 9.7 lbs. ASTM D 226 #15 (Type 1): 11.5 to 12. 5 lbs. Unrated (non-ASTM) #30 felt: 15.7 to 19.9 lbs. ASTM D 226 #30 (Type 2) felt: 26.4 to 27.3 lbs. Other relevant information from the article: "Asphalt felt, which has been around for over a hundred years, was originally a true cloth felt. "A long time ago, they used rag felt, which was cotton," says Dodie Webster, technical services manager at Tamko Roofing in Joplin, Mo., a manufacturer of asphalt felt. "But we can't get cotton rags any more." Since present-day asphalt felt is a paper product, the term "felt" is somewhat of a misnomer. "Unsaturated felt is basically composed of recycled corrugated papers mixed with sawdust," Webster says. Over the years, asphalt felt has also gotten lighter. "In the old days, it used to weigh 15 pounds per 100 square feet, but not anymore," says Allen Snyder, product engineer at CertainTeed, a manufacturer of asphalt felt. The main reason manufacturers make light-weight felts is because they're cheaper. "The whole issue comes down to price," says Ed Todd, technical manager at Atlas Roofing, an asphalt felt manufacturer in Atlanta. "This is a price-sensitive product," Todd says. Manufacturers now call their product "number 15" felt instead of 15-pound felt, and it weighs anywhere from 7 to 14 pounds per square. "ASTM has established two standards for asphalt felt. The less stringent standard is ASTM D 4869, which requires Type 1 (#15) felt to weigh at least 8 pounds per 100 square feet. The more rigorous standard, ASTM D 226, requires a minimum weight of 11.5 pounds per square. Most lumberyards stock only light-weight asphalt felt with no ASTM rating. "We sell a lot of the lightweight felts, the non-ASTM #15," says Webster. "It is probably our biggest seller." This type of #15 felt sometimes weighs only 7.6 pounds per square. There are a few regions where ASTM-rated felt is widely available, however, because of code requirements. "The most stringent felt market in the U.S. is Florida," says Ed Todd, of Atlas Roofing. "In Florida, at a minimum you must have 'ASTM D 4869' on the wrappers." "Asphalt felt is also available in a heavier version, commonly called 30-pound felt. This #30 felt is available in both the unrated grades and the ASTM-rated felts. ASTM standards refer to #30 felt as Type 2. The lightest unrated #30 asphalt felt is still heavier than the heaviest ASTM-rated #15 felt, making it a logical choice for concerned builders. "Asphalt felt has a permeance of only 5 perms when dry, but a much higher rating of 60 perms when wet. Fans of felt note one of its advantages over housewrap: If water gets behind felt - either due to a flashing leak or condensation from solar-driven moisture - the felt can soak up the liquid water and gradually dry to the exterior."
What is equivalent astm for is 2062 gr b?
ASTM A 516 Gr 60 Lalit Mohan kOthari
What is the russian ''gost'' standard equivalent of astm a615 gr 60 reinforced iron bar-rebar?
The Russian GOST standard equivalent to ASTM A615 Grade 60 reinforced steel rebar is GOST 5781-82, specifically the steel grade A500C. This standard specifies the requirements for hot-rolled steel bars used in concrete reinforcement, similar to the properties defined in ASTM A615. The GOST rebar typically has a yield strength of 500 MPa, aligning closely with the Grade 60 designation in the ASTM standard.
What the full answer to 60 and divide240?
0.25
What is the full form of 6G in welding?
In my point you, every 60 degree the welding was carry on.
What is the upper limit of ultimate tensile strength of ASTM-615A bars above which rejection is recommended?
Why would you reject material that overperformed its tensile-strength specs? The standard for Concrete Reinforcement rebar,astm-615a Grade 60 (60,000 PSI minimum yield strength)
What is the ultimate yield strength of astm 1018 steel?
ASTM 1011 comes in many grades which determine the yield strength ie:1011 gr 42 would have a min yield of 42,000 psi
What fraction of a minute is 39 seconds?
A full minute is 60 seconds, so 39 sec = 39/60 minute = 13/20 minute, in simplest form. It is 0.65 minutes in decimal.
What is 49 60 in decimal form?
49/60 in decimal form = 0.816749/60:= 49 ÷ 60= 0.8167 in decimal
What is 41 60 in simplest form?
41/60 is in its simplest form.
How many arc seconds are in a full circle?
There are 360 degrees in a full circle. 60 minutes in 1 degree 60 seconds in 1 minute Therefore: 360 x 60 x 60 = 1,296,000 seconds
How many full days are in 900 000 seconds?
There are 900,000/24*60*60 = 10 full days
What is the simplest form of 49 over 60?
49/60 is the simplest form.
