answersLogoWhite

0

The function of back pressure valve is to prevent back flow to the pump in case there is an obstruction on downstream side of valve.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

How the back pressure in a boiler calculated?

This question can't be answered. It is unclear what you mean by back pressure. Maximum Allowable Working Pressure in a boiler is calculated using the rules for construction of high pressure boilers and construction of heating boilers in the ASME Code sections 1 and 8.


Can you bleed a combi boiler?

Yes you can bleed a combi boiler. You do just the same as with a conventional boiler. However, the pressure will drop in your system, so you simply need to adjust it using the little tap (usually below the boiler) to bring it back again (Usually aronud 1.5)


How do you increase pressure on a pressure reducing valve?

Loosen the nut on top. Tighten the screw clockwise to increase, counter-clockwise to decrease pressure. Tighten the nut back up. Done deal


What is the purpose of having a back pressure valve in marine refrigeration system?

when two refrigerated spaces are severed by only one compresser & condenser but need to be maintained at different temps. a back pressure regulator comes into play. The back pressure regulator will be installed on the outlet of the refrigeration system to maintain a minimum back pressure in the evap coils. Since pressure is directly related to temp. then the temp. desired can be maintained by the pressure you set.


What is function of safety valve in boiler?

A safety valve in any reservoir or tank is used to prevent the tank from exploding from over-pressurization. Tanks filled with gas may become overpressurized when heated. Also during instances of filling the tank, the operator may be distracted and cause the tank to be over-filled. This safety valve will blow and thus preventing an explosion of the tank.

Related Questions

What is the feed check valve of boiler?

The feed check valve of a boiler is on the line coming out of the boiler it is usually to prevent the water from going back in to the boiler its coming out of so it would build up excessive amounts of pressure which will cause the t&p valve to blow temperature and pressure


What is a boiler check valve?

*A boiler check valve is usually made by Watts and called a Watts 9D. This prevents the water that goes into the boiler backflowing and having the heating water from the boiler coming back into the domestic water and having you drink it or shower in it.* Cheers,QuiteSomething


Can you use a bladder pressure tank even though the bladder is leaking?

If your bladder is damage in any way, your boiler will run but you will have other problems.If your expansion tank is not working, you will be seeing water leaking out of the Pressure Relief Valve when pressure gets around 30psi (most residential boilers). The water may stop dripping when the boiler reaches its highest temperature, but once the boiler starts cooling down, water will start contracting causing low pressure. This will cause the automatic fill valve to let water back into the boiler thus making the water drip out the relief valve again when it heats up.DO NOT shut off the water inlet valve. This could cause high damage or seriously injury if you run out of water.You should replace the tank and also the relief valve to be safe. Call a licenced plumber.


How does a back boiler work scientifically?

A boiler works by heating water in an enclosed space. The expansion of water molecules as it transforms from a liquid state into a gaseous one causes the boiler to generate a vast amount of pressure. This is generally the science behind a back boiler.


How the back pressure in a boiler calculated?

This question can't be answered. It is unclear what you mean by back pressure. Maximum Allowable Working Pressure in a boiler is calculated using the rules for construction of high pressure boilers and construction of heating boilers in the ASME Code sections 1 and 8.


Why boiler is in vaccumed condition?

Because you forgot to open the vent when the pressure dropped below 15 psig. A boiler under vacuum will suck in its handholes and manholes, and they might start leaking when pressure is put back on them. weakened boiler parts can fail as well.


Function of root blower in cfbc boiler?

the pressure of the root blower is higher then the wind box pressure, because what ever the unburnt particle come from cyclone separator is collect in return leg this unburnt particle return back into combustion chamber so the function of root blower is to continuous circulation.


What is the function of suction valve in refrigeration system?

Once the fluid travels through the radiator on the back of the refrigerator, the valve will open and use the force of the piston retracting to suck the fluid into the compressor, where the pressure will cool the refrigerant over again.


What is the function of the valve found in this location?

To stop the back flow of blood.


Can you bleed a combi boiler?

Yes you can bleed a combi boiler. You do just the same as with a conventional boiler. However, the pressure will drop in your system, so you simply need to adjust it using the little tap (usually below the boiler) to bring it back again (Usually aronud 1.5)


How does Back-pressure valve work in dairy production?

Back pressure regulating valve is used in ammonia refrigeration plant to maintain the minimum pressure in the evaporator coils. It helps in preventing ice formation / choke upin the PHE chiller.


What type of boiler should replace my Baxi Bermuda back boiler?

A system or combi boiler is a great replacement for a Baxi back boiler. Boiler Hut can help with selection and installation.