0
What else can I help you with?
What is the current of 1MVA transformer?
This depends on the voltage, and whether it is a three phase or single phase transformer.
What would the input current be for a 275 kva transformer with 2 phase of a 480 vac in and 120 vac at 20 amp output?
qsq
How do you design a transformer with three phase 400v input and single phase 2000v output?
By design are you going to wind the transformer yourself? In your design you need a 5:1 ratio. On the output side of the transformer any two legs of a three phase transformer is considered single phase voltage. Good luck on your project.
What is phase angle error of current transformer?
The angle between the expected and actual secondary current is known as phase error.
What is the angle between no load current and the applied voltage in an ideal transformer?
A: Transformer by itself goes not alter the phases the output can be in phase or out of phase depending how you look at it.
What is the current of 1MVA transformer?
This depends on the voltage, and whether it is a three phase or single phase transformer.
What would the input current be for a 275 kva transformer with 2 phase of a 480 vac in and 120 vac at 20 amp output?
qsq
How do you zero phase current tranformer test?
How do you zero phase current transformer test
How many amps do you need to supply a 150kva transformer to get 118amps 480 volts?
Rephrase your question, as it doesn't make any sense. If the primary side of the transformer is 480 volts 3 phase, this transformer can be supplied from a breaker as big as 180 amps. If 480 volts 3 phase is your secondary then you can supply up to 180 amps to your loads.
How do you convert a 3-phase system to a single phase?
By having a transformer with 3 phase input and single phase out put
How do you design a transformer with three phase 400v input and single phase 2000v output?
By design are you going to wind the transformer yourself? In your design you need a 5:1 ratio. On the output side of the transformer any two legs of a three phase transformer is considered single phase voltage. Good luck on your project.
What is phase angle error of current transformer?
The angle between the expected and actual secondary current is known as phase error.
What is the angle between no load current and the applied voltage in an ideal transformer?
A: Transformer by itself goes not alter the phases the output can be in phase or out of phase depending how you look at it.
A single-phase transformer when supplied from 220v50hz has eddy current loss of 50wif the transformer is connected to a voltage of 330v50hzthe eddy current loss will be?
112.5
Why does a phase in secondary side in distribution transformer give low voltage?
transformer is busted; if input voltage is normal you have short circuit or open circuit somewhere
How many coils are there in a transformer?
There are normally only one set of primary windings in a transformer. Some may have multiple windings though so that they can cover a wider range of input voltages.
How many 16 Amps per phase welding outlet can you install to a 30 KvA rating transformer?
..the questions does not say wether the 30kVA transformer is 3 phase transformer or single phase transformer..but it is implying that a single phase welding load at 16A per phase is to be connect to it, it is assumed then that the transformer is 3 phase transformer..we assume load is rated 240V.. ..though not much details is given about the transformer voltage specs. but if is rated 3 phase 415/240V, the approx full load current per phase is given by 30KVAx1.3912=41.736A.. ..but if the transformer was rated single phase 240V say, the approx full load current FLC=30000/240V gives 125ampers.. ..if you further devide the FLC by the intended load current.. ..Recommended no of welders per for a 3 phase 415V transformer and assuming single welding sets =41.736/16=2.6..so you can connect max two welding sets to this transformer per phase,..max 6 weld sets can connect at an approx load factor of 76%.. ..for the single phase transformer, FLC/16=125/16, gives 7.8 but is also recommended not to connect more than 6 welding sets to such transformer for the same reasons..
