0
What else can I help you with?
What is the value of allowable bending moment of plywood?
12mm thk
If an array has a 100 elements what is the allowable range of subscripts?
Since arrays in C are zero based, the allowed subscript range is 0 - 99 (gives 100 values). Always remember to subtract 1 from the high range (in this case 100) to get the last subscript maximum value.
What is the maximum absolute value reached by a voltage or current waveform?
define the maximum value of an ac wave form
What is the maximum value power capacity of dry type transformer?
What's the maximum value power capacity of dry type
How do you calculate allowable leakage for HDPE pipes uring pressure hyodro pressure testing?
0.2 x(dia of pipe)x(length of pipe) For examble if you have 100mm diameter pipe and 50 m length .. 0.2x0.1x50= 1 litre and this is your allowable value
What is allowable stresses?
The maximum allowable stress is that value beyond which, after applying an appropriate factor of safety its particular strength criterion is exceeded and failure occurs. For example, if aluminum strength in yield is 35,000 psi, and factor of safety is 1.25, its maximum allowable stress against yield is 35,000/1.25 = 28,000 psi
What is the allowable stress for material S355?
The allowable stress for S355 steel typically depends on its application and design standards. In general, the yield strength of S355 is around 355 MPa, and the allowable stress is often taken as a fraction of this value, usually around 0.6 to 0.7 times the yield strength, depending on the safety factors applied. For structural applications, this can translate to an allowable stress of approximately 210 to 250 MPa. Always consult relevant design codes for precise calculations.
What is maximum safe femur load in a car crash?
The maximum safe femur load, according to SAE is the allowable injury assessment value. The maximum femur load is 2250 lbs.
What SA-212 Grade B stress value?
SA212-Grade B was a type of steel used in building during the midcentury. It had a basic allowable stress of 17,500 psi up to 650 degrees (F).
What is the meaning of derating factor?
A transistor rating that tells how much the maximum allowable value of PD decreased for each 1°C rise in ambient temperature.
Why maximum stress concentration factor for plate with a hole is 3?
Maximum stress concentration factor on a plate with a circular hole depends on the radius/size of the circle and the overall width of the plate. So the value can be different then 3
What is the value of allowable bending moment of plywood?
12mm thk
What is maximum value?
What is maximum value
What is the different between fatigue and creep?
Both Fatigue and Creep are causes of failure of a material at a stress value significantly below the Allowable threshold. They differ from each other in the sense that fatigue is defined as the failure of a material, subjected to multiple loading and unloading cycles, even though, in none of the instances, the applied stress crosses the Allowable stress value. The fatigue life of a material is usually specified in # of loading/unloading cycles it can undergo, without failing. The fatigue life decreases as the applied stress approaches the Allowable Stress. CREEP, on the other hand, is time related failure of a material. Creep, explains that a material subjected to a certain applied stress will continue to deform at that constant stress value. Hence, creep results in an increase in strain value while the stress is constant, until it causes the failure of the subject material. CREEP tends to increase with the temperature of the specimen
What value or values of m1 are allowable for an orbital with i equals 2?
2
What theory of failure is used for ductile materials?
For ductile materials, teh VonMises theory is used; it combines tension and shear stresses in a different way than principal stress, which is used for brittle materials. In either case, its value is compared to the normal (tension/compression) stress allowable for the particular material.
What is maximum permissible stress?
The maximum allowable stress is that value beyond which, after applying an appropriate factor of safety its particular strength criterion is exceeded and failure occurs. For example, if aluminum strength in yield is 35,000 psi, and factor of safety is 1.25, its maximum allowable stress against yield is 35,000/1.25 = 28,000 psi
