answersLogoWhite

0

The minimum current required to turn on a thyristor is called the "gate current" or "trigger current." This is the amount of current that must be supplied to the gate terminal to initiate the conduction process of the thyristor. Once the thyristor is turned on, it will continue to conduct even if the gate current is removed, as long as the anode current remains above a certain threshold known as the "holding current."

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Continue Learning about Engineering

What is the difference between current and voltage commutation?

Voltage commutation: This is possible in ac circuits...The thyristor gets turned off by reverse bias (negative half cycle) voltage applied across it. This is also called line commutation. Current Commutation: This is possible in dc circuits ...This type of commutation makes use of auxiliary circuit which contains inductor,capacitor,diode and even a thyristor(auxiliary). This is called Forced commutation.


What is commutation of a rectifier?

Commutation in a rectifier: Refers to the process of transfer of current from one device (diode or thyristor) to the other in a rectifier. The device from which the current is transferred is called the "out going device" and the device to which the current is transferred is called the "incoming device". The incoming device turns on at the beginning of commutation while the out going device turns off at the end of commutation.Commutation failure: Refers to the situation where the out going device fails to turn off at the end of commutation and continues to conduct current.


Why thyristor is also called as silicon controlled rectifier?

For the same reason that its used in transistors and resistors...Its a semiconductor.


How does a transistor electronically switch the output on?

A transistor can electronically switch the output by controlling the flow of current between its two terminals, called the collector and emitter. It has a third terminal, called the base, which acts as a control input. When a small current is applied to the base terminal, it influences the flow of current between the collector and emitter terminals, effectively turning the transistor "on" or "off" and allowing it to change the output state.


Current in which electrons flow in the same direction is called?

It's alternating current

Related Questions

What is line commutation?

i think i know this answer...line commutation is the commutation in single phase inverters/converters when there is current flow back to the source.. It can also refer to a method of turning of a semiconductor device known as a Thyristor or SCR, sometimes called natural commutation. In this method the current between the anode and cathode is interrupted or dropped to a point where the Thyristor can no longer maintain its latch or keep conducting, shutting the device off.


What is the use of thyristor?

Function of a thyristorA thyristor - also known as an SCR (silicon controlled rectifier) - is like a very fast static switch and is good for controlling large amounts of power (called power regulation) and for controlling the speed of dc motors. Another typical application is to make dimmers for lighting circuits.How it worksA thyristor is semiconductor device having 3 electrodes:an anodea cathodea gateNo current can travel from the anode to the cathode until a pulse which has the right amount of voltage (called the "trigger voltage") has been applied to the gate for the right minimum amount of time (called the "trigger duration") which causes the thyristor to switch on to allow current to flow through it from the source to the load.After being triggered, current continues to flow through the thyristor from the source to the load until either:the load gets disconnected from the thyristor by some other means orthe supply of current from the source to the thyristor gets turned off by some other means.


What is an off-state condition of thyristors?

thyristor can be turned off only by reducing the anode current belaw a certain value called holding current by abdullahi yusuf gedi


What is the difference between current and voltage commutation?

Voltage commutation: This is possible in ac circuits...The thyristor gets turned off by reverse bias (negative half cycle) voltage applied across it. This is also called line commutation. Current Commutation: This is possible in dc circuits ...This type of commutation makes use of auxiliary circuit which contains inductor,capacitor,diode and even a thyristor(auxiliary). This is called Forced commutation.


What is The turning point of a parabola?

the vertex, or very bottom point.I can also be called the maximum or minimum.


What is the difference between firing and triggering a thyristor?

There is no difference. The terms "firing" and "triggering" both mean exactly the same.As long as the voltages applied to both the anode and the gate have the correct values and polarities for a particular design of thyristor, "firing" or "triggering" will cause current to switch on between the thyristor's anode and cathode. The current will then continue to flow for as long as the correct source voltage polarity is maintained onto the anode.Another opinionIf the input signal is given to a thyristor, it is said to be gated. Because of gating pulse the thyristor gets triggered ( cause & effect relationship). Once the thyristor is triggered the charged particles starts moving inside the different layers. A noise is created called "SHOT NOISE", due to the movement of charged particles. Heat energy is dissipated due to this movement of charged particles. Once the thyristor reaches this stage it is said to be fired. Hence, there is a minute difference between these three terms. But all these terms are being used interchangeably.


What is the thyristor firing circuit?

The thyristor is basically used a switch in an AC circuit to control the amount of power fed to the load. To turn on this switch an "electric" pulse should be applied to the Gate terminal of the Thyristor. A circuit which supplies the "electric" pulse is called the firing circuit.


Why thyristor is called controlled device?

its output voltage can be conrolled by changing gate signal akash pilani


What is commutation of a rectifier?

Commutation in a rectifier: Refers to the process of transfer of current from one device (diode or thyristor) to the other in a rectifier. The device from which the current is transferred is called the "out going device" and the device to which the current is transferred is called the "incoming device". The incoming device turns on at the beginning of commutation while the out going device turns off at the end of commutation.Commutation failure: Refers to the situation where the out going device fails to turn off at the end of commutation and continues to conduct current.


What is the turning point of a graph called?

The turning point of a graph is called a "critical point" or "extremum." In calculus, these points occur where the derivative of a function is zero or undefined, indicating a local maximum or minimum. At these points, the graph changes direction, which can represent peaks or valleys in the function's behavior.


What is it called when you turn light into electrical energy?

The process of turning light into electrical energy is called the photoelectric effect. This phenomenon occurs when light photons strike a material's surface and eject electrons, thereby generating an electric current.


What is a nail wrapped around a wire and connected to a battery called?

It is called an electromagnet. When electric current flows through the wire, a magnetic field is created, turning the nail into a temporary magnet.