answersLogoWhite

0

As far as I have been taught there is no maximum thickness allowed for a shim. Shims can be specially made out of thicker plate to achieve the correct alignment. The only restriction I know about with shims is that there should never be more than 3 shims in one place (e.g. only 3 shims are allowed under each motor foot).

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Engineering

What is steel shim spike protectionon work boots?

The steel shim spike for protection on work boots is called a tongue protector. This type of protector is common on boots worn by people who handle very heavy equipment and welders. The spike fits over the tongue of the boot just inside the laces.


Can a screwdriver be used as a wedge?

It can, but this is a mis-use of the tool and can bend it. Better to use a wood or metal shim wedge. Available cheap in all good tool stores.


What is a shim used for in construction?

In construction, shims are often used to align two pieces of lumber. They can also be used to fill or align gaps between larger objects and to make objects level.


What is the recommen ded way to hold a loose hub on a fan?

To hold a loose hub on a fan, it's recommended to tighten the hub set screw securely against the motor shaft, ensuring a snug fit. If the hub is still loose, you may need to use a shim or a locking compound to improve the grip. Additionally, regularly check for wear and tear on the components, as this can affect the hub's stability over time. Always follow the manufacturer's guidelines for any specific instructions related to your fan model.


Why don't the upstairs cast iron radiator heaters work?

Most often because they become air/water-locked. A cast iron radiator system works by sending steam (which naturally rises) up from the lower level into each radiator. When the steam heats the cast iron it loses enough heat so that it cools back to a water (liquid) state. When this happens, the water must flow back to the burner all by itself, propelled ONLY BY GRAVITY. So if at any point in the loop ANY length of pipe has sagged so that it is not downhill enough to allow the water to drain, the system will become locked at that point and no steam will pass by, thus cutting off heat to all radiators beyond the blockage. The most common fix for this is putting shims underneath the feet of the radiator on the opposite side of the pipe only, thus angling the radiator down for full drainage. Many times people will cause the issue themselves by putting a floor or tile underneath the radiator, inadvertently removing the angle. Other times, the natural sagging of the house removes the angle put in when the system was originally installed. So, your best bet is to 1.) Shim all non-working radiators downward toward the pipe, 2.) Drain the whole system (from the spigot at the base of the burner) of all water (and air), and 3.) re-fill the burner with water to the appropriate water pressure. Replacing the steam valves on each non-working radiator is a good idea as well.

Related Questions

What is the purpose of a striker plate shim and how does it affect the installation of a door striker plate?

A striker plate shim is used to adjust the position of a door striker plate so that it aligns properly with the door latch. It helps ensure that the door closes securely and smoothly. The shim can be inserted behind the striker plate to make small adjustments in its position, which can be crucial for proper installation and functionality of the door.


What is the purpose of a strike plate shim and how does it contribute to the installation of a strike plate?

A strike plate shim is used to help align the strike plate with the door latch. It fills any gaps between the strike plate and the door frame, ensuring a secure and proper fit. This contributes to the installation of the strike plate by improving the overall security and functionality of the door lock.


What is Cathy Shim famous for?

Cathy Shim, born July 18, 1980 is a Korean-American actress and film producer. Shim was most known for appearing in a variety of TV shows, like Reno 911!, MADtv and Drake & Josh.


What does shim mean in Hebrew?

"shim" is not a Hebrew word"


When was Mark Shim born?

Mark Shim was born in 1973.


When was Shauna Shim born?

Shauna Shim was born in 1979.


what is the height of a stack of 13 of these steel shims. if you have a rectangle at 1.27cm?

To determine the height of a stack of 13 steel shims given a rectangular shape with a thickness of 1.27 cm, we need to calculate the total height by multiplying the thickness by the number of shims in the stack. Height of one shim = 1.27 cm Number of shims = 13 Total height = Height of one shim * Number of shims = 1.27 cm * 13 = 16.51 cm Therefore, the height of a stack of 13 steel shims, each with a rectangular shape of 1.27 cm thickness, is 16.51 cm.


How do you adjust the valve on a 93 4runner V6 Eng?

the valves on this motor are adjusted by means of shims that go between the cam lobes and carriers which are also called buckets. the combination of the shim and bucket are pushed down by the cam lobe onto the top of each valve, thus opening the valve. adjusting the valves is a matter of measuring the clearence between the shim and cam (when the lobe is completely opposite the shim) if there is too much clearance a thicker shim must be used, if there is not enough clearance a thinner shim must be used. there is a chart in the repair manual because you not only have to know the clearance but the actual thickness of the shim so you can order the proper replacement shim. its not an easy job and is very time consuming. the intake plenum and cam covers have to be removed just to check them. if there needs to be an adjustment, you have to order a very specific shim size based upon very accurate measurement and calculation. good luck!


What nicknames does Beomsik Shim go by?

Beomsik Shim goes by Shimbe.


How do you pronounce Schim Schimmel?

It is pronounced as "SHIM SHEE-mel." The "ch" in the first name is pronounced as "sh" like in "shoe," and the second name sounds like "shim-el."


How tall is Cy Shim?

Cy Shim is 5' 7 1/2".


When was Shim Mina born?

Shim Mina was born on 1972-12-10.