answersLogoWhite

0

The process of connecting electrical components to a circuit board is

known as glueing, cementing, strapping, or bolting.

The process of connecting components electrically to points in the circuit is

known as soldering.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

What is the meaning of electrical components?

Electronic component are those component which are used to make the electronic circuit it may be active or passive . some active components are - Diode ,FET,BJT,MOSFET, and HEMT etc. while passive component are those device which can not process/amplify signal like- resistor capacitor inductor etc.


When was the integrated circuit made?

1958, but the germanium based process was difficult and expensive to use, requiring all the components in the IC be interconnected by hand under a microscope. It took another year or so for the silicon based planar process to be used, which allowed all components and interconnects to be made using photolithography.


What an electrical cell is and how it causes a current in an external circuit?

An electrical cell is the basic unit from which electrical batteries are made. The cell is composed of two plates made of different conductive materials and a liquid electrolyte (in "dry" cells this liquid is in the form of a moist paste). Electric charge is produced between the two plates by the electrolyte interacting with and causing corrosion of one or both plates. Once the electric charge is produced the corrosion process slows or stops, unless an external circuit is connected between the plates. When an external circuit is connected between the plates, current flows through that circuit and the electric charge is slightly reduced. The corrosion process continues at a rate necessary to maintain the electric charge, until the chemicals in the cell are used up.


What is the process of circuit design?

The circuit design process covers systems ranging from highly complex to simple. The design process for simple circuits can usually be completed by one person, while teams of designers may be required to complete the process for more complex circuits.


What is the importance of statistics in electrical engineering?

importance of statistics in electrical engineering

Related Questions

What is the process for replacing a switch in an electrical circuit?

To replace a switch in an electrical circuit, first turn off the power to the circuit at the breaker. Remove the cover plate and unscrew the switch from the electrical box. Disconnect the wires from the old switch and connect them to the new switch in the same way. Screw the new switch into the electrical box and replace the cover plate. Turn the power back on at the breaker to test the new switch.


What is the meant by the following term Assembly process?

The term 'Assembly Process' is when you build and put together all the parts to create something, for example: 'The assembly process of a computer would be to connect all the electrical components together to make it work.'


What is the significance of starting resistance in electrical circuits?

Starting resistance in electrical circuits is significant because it helps limit the initial flow of current when a circuit is turned on. This can prevent damage to components and ensure a smooth and controlled start-up process.


How does a resistor reduce voltage in an electrical circuit?

A resistor reduces voltage in an electrical circuit by converting some of the electrical energy into heat. This process slows down the flow of electricity, resulting in a decrease in voltage across the resistor.


How do you properly wire a 2 pole breaker in an electrical circuit?

To properly wire a 2 pole breaker in an electrical circuit, connect the hot wires to the breaker terminals, the neutral wire to the neutral bus bar, and the ground wire to the ground bus bar. Make sure to follow the manufacturer's instructions and turn off the power before starting the wiring process.


What is a printed circuit board?

A printed circuit board is basically used to mechanically support while at the same time electrically connecting electronic components by using conductive pathways. The process is very simple.motherboard is a printed circuit ,where all components of the system is connected.Printed circuit boards are used in nearly all electronic devices.The conducting wires that connect all the components, are printed onto an insulating plastic material such as paxolin or fiberglass. These tracks are commonly made of thin copper sheet stuck to the board. The tracks are then printed using light and a chemical process to remove the unwanted copper.Some boards used in remote controls and wafer thin boards used in ipods etc, are commonly printed, using conductive ink containing silver or carbon.The alternative to printed circuits was to idividually wire the coponents using wire and solder tags. Old tube radios were originally wired this way, but had to be made by hand.Printed circuits allow for automation and mass soldering using a float soldering process on a bed of molten solder.


What kind of electrical circuit can sense an electrical signal process it and give an electrical output?

Automatic garage door opener with a remote The answer above will give a mechanical output not an electrical output. Photocells come to mind.


What is the meaning of electrical components?

Electronic component are those component which are used to make the electronic circuit it may be active or passive . some active components are - Diode ,FET,BJT,MOSFET, and HEMT etc. while passive component are those device which can not process/amplify signal like- resistor capacitor inductor etc.


How can electrical testing meters aid in the troubleshooting process of an appliance?

Electrical testing meters can definitely aid in the troubleshooting process of an appliance. This is because if it reads "no voltage" when plugged into the outlet, then the fuse or circuit is at fault, not the appliance.


How can I eliminate a 3-way switch from my electrical circuit?

To eliminate a 3-way switch from your electrical circuit, you can rewire the circuit to convert it to a single-pole switch setup. This involves identifying the wires connected to the 3-way switch and rerouting them to a single switch configuration. It is important to turn off the power to the circuit before attempting any electrical work and consult a licensed electrician if you are unsure about the process.


How is the push feature utilized in electrical connectors to ensure secure and reliable connections?

The push feature in electrical connectors is used to securely and reliably connect two components together. By pushing the connector into place, it ensures a tight and stable connection, reducing the risk of disconnection or electrical failure. This feature is designed to make the connection process easier and more efficient, while also improving the overall reliability of the electrical connection.


How does a magnetic transformer work to convert electrical energy from one circuit to another?

A magnetic transformer works by transferring electrical energy from one circuit to another through electromagnetic induction. When an alternating current flows through the primary coil of the transformer, it creates a changing magnetic field. This changing magnetic field induces a voltage in the secondary coil, which then transfers the electrical energy to the secondary circuit. This process allows for the conversion of electrical energy from one circuit to another with minimal loss.