0
What else can I help you with?
Why do you need to have esp to calculate the u trap size for condensate drain in ahu?
Because the weight of the water in the trap must be greater than the esp or the trap will be ineffective,and the trap size dictates how much water it can hold thus determining the weight.
Do you need a trap on a bathtub?
YES, you do need a trap. Usually the bathtub drain is on the same sewer line as the nearby toilet.The smell from the toilet's discharge will sneak up through the bathtub's drain line without a trap ... not pleasant!.
What is the difference of a gully trap drain from a floor drain?
The difference between a gully trap drain and a floor drain is placement. A floor drain is in a floor, a gully trap drain goes on an external wall.
How can you tell if you have a trap in a drain line?
If you have a floor drain, there is a trap on the bottom of that. The main line shouldn't have a trap in it. There does not need to be one on the main because each fixture should have one and that's just another place for a clog to form.
Does a dishwasher need a p-trap?
Normally you will install a dishwasher drain pipe above your kitchen sink drain, so you are using the sinks P-Trap. When installed in this fashion, no you don't require a seperate. If you want to install your drain elsewhere, than yes you need a trap otherwise you will have sewer gases backing up through your dishwasher and into your kitfchen
What is the purpose of a condensate drain trap in an HVAC system?
The purpose of a condensate drain trap in an HVAC system is to prevent air from escaping or entering the system while allowing water to drain out.
What is the purpose of the HVAC condensate drain trap and how does it contribute to the overall efficiency of the system?
The purpose of the HVAC condensate drain trap is to prevent air from escaping the system while allowing water to drain out. This helps maintain proper airflow and prevents energy loss, contributing to the overall efficiency of the HVAC system.
Dose a positive pressure drain need a trap?
A trap on a positive drain is used to avoid the 'contaminated' air in a HVAC system from traveling through the condensate line and entering into areas where it is unwanted. The trap becomes necessary when one condensate line is used for multiple units, especially if it is tied to other negative pressure drain traps. The negative pressure drain traps may not drain properly if they have to overcome the positive non- trapped pressure of another unit. It allows the condensate to drain more evenly, as well. Without a trap, the positive pressure from the unit can blow air through the drain with the water and cause 'spitting.' A trap on a positive pressure system may not always be necessary, but it is good practice to trap every drain and trap it properly. There are guidelines for both positive and negative pressure traps. Always follow the manufacturers recommendations.
Why do you need to have esp to calculate the u trap size for condensate drain in ahu?
Because the weight of the water in the trap must be greater than the esp or the trap will be ineffective,and the trap size dictates how much water it can hold thus determining the weight.
Does a shower drain need a P-trap for proper drainage?
Yes, a shower drain needs a P-trap for proper drainage. The P-trap prevents sewer gases from entering the shower and also helps to maintain proper water flow by creating a seal that prevents clogs and odors.
What is the purpose of an HVAC condensate trap and how does it contribute to the overall efficiency of the system?
An HVAC condensate trap is used to prevent water from accumulating and blocking the system. It helps maintain proper drainage, preventing clogs and ensuring the system runs efficiently.
Why is central air unit sucking the water from the a- coil down and dripping on the motor It shorted out your breakers and you replaced them The water drain is clear What is causing this hard vacuum?
The issue could be due to a blockage in the condensate drain line, leading to a negative pressure causing the water to be pulled into the system. Check for any obstructions in the drain line, and ensure it is properly sloped for efficient drainage. Additionally, consider installing a safety switch to shut off the unit if the water level rises too high to prevent damage to the motor.
What is the washing machine drain code for proper installation and maintenance?
The washing machine drain code for proper installation and maintenance typically requires the drain hose to be secured above the level of the washing machine and to have a P-trap to prevent backflow. Regular cleaning of the drain hose and P-trap is also recommended to prevent clogs and ensure proper drainage.
Why does a shower drain need a trap?
A shower drain needs a trap to prevent sewer gases from entering the bathroom. The trap holds water to create a barrier that blocks the gases from coming up through the drain.
How does an inverted steam trap work?
An inverted steam trap works by allowing condensate to flow out of the system while preventing steam from escaping. When condensate builds up, the trap closes and prevents steam from passing through until the condensate is released. This helps maintain efficient operation by removing unwanted condensate and maintaining steam within the system.
Do you need a trap on a bathtub?
YES, you do need a trap. Usually the bathtub drain is on the same sewer line as the nearby toilet.The smell from the toilet's discharge will sneak up through the bathtub's drain line without a trap ... not pleasant!.
Does a shower require a trap for proper drainage?
Yes, a shower requires a trap for proper drainage to prevent sewer gases from entering the bathroom and to maintain the flow of water down the drain.
