answersLogoWhite

0

to protect or to calculate the operating conditions of an electrical system and to camand circuitbreaker to trip in any fault detection.relay is the one which detects the abnormal condition of the circuit and signals the circuit breaker to trip(open).....

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

What is the difference between an definite purpose contactor and a lighting sontactor?

A definite purpose contactor is designed (and rated) for a specific load. So a lighting contactor is one example of a definite purpose contactor. A motor starter contactor is another example. So, a lighting contactor is a definite purpose contactor, but a definite purpose contactor is not necessarily a lighting contactor (it might be a motor starter, for instance).


How do you put definite purpose contactor?

Depends on where you want to put it! Assuming, that you're asking ~how you'd "install" a Definite purpose contactor.


How does the push button off and on work with the relay and the contactor?

The push button operates a relay or contactor by momentarily completing an electrical circuit. When the button is pressed, it energizes the relay or contactor coil, which closes the corresponding contacts and allows current to flow to the load. Releasing the button de-energizes the coil, opening the contacts and stopping the current. This mechanism allows for remote control of high-power devices using low-power buttons.


What is a contactor for a Central Air Unit?

The relay actuated by the thermostat which starts and stops the compressor and condenser fan in the outdoor unit.


What is the different between contactor and relay?

A contactor, as far as being used to start a motor or the like, is in essence, a relay. A coil is energized and the normally open contacts from the contactor close (normally 3 contacts for an AC motor) and the motor starts. Do I understand your question? Or are you trying to decifer the difference between the coil of a relay and the contacts of a relay?

Related Questions

What is the difference between an definite purpose contactor and a lighting sontactor?

A definite purpose contactor is designed (and rated) for a specific load. So a lighting contactor is one example of a definite purpose contactor. A motor starter contactor is another example. So, a lighting contactor is a definite purpose contactor, but a definite purpose contactor is not necessarily a lighting contactor (it might be a motor starter, for instance).


What is the part of the contactor that gets magnetized by the relay coil is called what?

The part of the contactor that gets magnetized by the relay coil is called the armature or plunger. This is the component that moves when the relay coil is energized, causing the contacts to close or open depending on the design of the contactor.


How do you wire a relay to a motor contactor?

One way is to use the auxiliary contacts on the motor contactor to close a separate source supply to drive an auxiliary relay.


How do you put definite purpose contactor?

Depends on where you want to put it! Assuming, that you're asking ~how you'd "install" a Definite purpose contactor.


Can you replace an 3 phase solid state relay with a contactor on a 3 phase heater?

Not without other modifications. The circuits used to turn the solid state relay on will not be suitable for turning a contactor on.


How relay is used to control induction motor?

If you want to control induction motor using a control relay give neutral directly to the one point of coil of relay & one point of coil of contactor then give control supply through push button to second point of coil of relay. use one NO point of relay and give supply to coil of contactor. and also use one NO of contactor for holding the contactor & take OFF (NC) in the starting to stop motor after complition of work. It is jut like an Direct On-line starter.


How does the push button off and on work with the relay and the contactor?

The push button operates a relay or contactor by momentarily completing an electrical circuit. When the button is pressed, it energizes the relay or contactor coil, which closes the corresponding contacts and allows current to flow to the load. Releasing the button de-energizes the coil, opening the contacts and stopping the current. This mechanism allows for remote control of high-power devices using low-power buttons.


What device is the only load in the control circuit of a condensing unit?

I think that would have to be some relay or contactor coil for a fan, compressor or relay contacts.


What is the difference between a contactor and a relay in electrical systems?

A contactor is typically used for high-power applications and has larger contacts, while a relay is used for lower-power applications and has smaller contacts. Contactors are designed to handle higher currents and voltages than relays.


What is the difference between a contactor and a relay?

A contactor is typically used for high-power applications, while a relay is used for lower-power applications. Contactors have larger contacts and are designed to handle higher currents, while relays are more compact and suitable for smaller loads.


If condencer contactor goes out...will it stop blowing cold air?

this is most likely a relay under the hood.


What is the difference between a relay and a contactor?

A relay is a switch that is operated by electricity, typically used in low-power applications. A contactor is a larger switch that is used in high-power applications, such as controlling motors or lighting. Contactors are designed to handle higher currents and voltages than relays.