0
What else can I help you with?
Can the vent pipe for the toilet have an elbow in it?
Yes.
What data is needed to fabricate a 16 inch pipe elbow?
hi need ur help 4 dis . What data is needed to fabricate a 16 inch pipe elbow?
Degree of a bevel for pipe?
37 degree
How do you fix a plumbing vent pipe?
Plumbing vent pipe is installed through a cathedral ceiling and metal roof surface there is no easy access into the roof cavity. In an attic after cut off the elbow whose female end contained the remains of the ABS pipe, glued on a short extension and new elbow in the attic, and glued a new plumbing vent rooftop riser into the new elbow. For more information visit at: alliedallcityinc.com
How do you fabricate elbows by cutting from a straight pipe then welding the cut parts to form an elbow?
for example : if we take a size of diameter 480mm fabricated pipe of wall thickness 3mm from this we going make a elbow by formula CMof Circle X required degree by 360 X 2 X no .of cut needed = 1520 X 90 / 360 X 2 X 3 = 64mm make a divde four lines on pipe mark of line of half of diameter = 220mm in two lines next to next parallel mark 6.4 cm by one half to another half on both lines then u make cut it u will get elbow
What is the take out of a 6 inches socket weld 90 degree elbow?
what is the take out of 6 inches pipe of a socket weld 90 degree elbow
What is the take out of 6 inches socket weld 90 degree elbow?
what is the take out of 6 inches pipe of a socket weld 90 degree elbow
What is the face to centre measurment of s 18 inch 45 degree elbow?
The face-to-center measurement of an 18-inch 45-degree elbow is typically 12.75 inches. This measurement is calculated based on the standard dimensions for fittings, where the centerline offset for a 45-degree elbow is approximately 0.75 times the diameter of the pipe. However, it's always advisable to refer to specific manufacturer specifications for precise dimensions, as they can vary slightly.
What is the take out for a 4 long radius degree weld ell?
The take-out for a 4-inch long radius degree weld elbow (or ell) is typically determined by the radius of the elbow and the pipe diameter. For a long radius elbow, the centerline radius is usually 1.5 times the pipe diameter; therefore, for a 4-inch diameter pipe, the centerline radius would be 6 inches. The take-out length is generally the distance from the end of the pipe to the point where the elbow connects, which can be calculated based on the elbow's radius and the angle of the bend. For a 90-degree elbow, the take-out would be approximately equal to the radius plus the straight length of the pipe before and after the elbow, typically resulting in about 9 to 10 inches.
What are end to centre measurement of 6 no 10 victaulic 90 elbow?
The end-to-center measurement for a 6-inch, Schedule 10 Victaulic 90-degree elbow typically measures approximately 4 inches. This measurement is taken from the end of the pipe to the centerline of the elbow. However, it's important to refer to the manufacturer's specifications or installation guides for precise measurements, as they can vary slightly depending on the specific product design.
What is the formula to find take off for 30degree elbow?
The take-off for a 30-degree elbow can be calculated using the formula: Take-off = Pipe Diameter × 0.577. For example, if the pipe diameter is 4 inches, the take-off would be 4 × 0.577 = 2.308 inches. This formula helps determine the horizontal run of the pipe after the elbow joint.
What is the take off for a 4 inch 90 degree elbow?
The take-off for a 4-inch 90-degree elbow is typically calculated based on the diameter of the pipe and the angle of the bend. For a 4-inch diameter pipe, the take-off is generally around 10 to 12 inches. This measurement may vary slightly depending on the specific design and manufacturer of the elbow, so it's always best to refer to the manufacturer's specifications for precise dimensions.
What is the take off formula off 45 degree elbow pipe?
The take off formula of a 45 degree elbow pipe, will depend on what the pipe is on. Sometimes a 45 degree pipe will need a 90 degree right angle turn to come off.
What is takeoff measurement on a 4 inch victaulic 90?
Takeoff measurement for a 4-inch Victaulic 90-degree elbow typically refers to the distance from the centerline of the pipe to the end of the fitting. For a standard 4-inch Victaulic elbow, this measurement is generally around 4 inches, but it can vary slightly based on the specific manufacturer and design. Always consult the manufacturer's specifications or installation guidelines for precise measurements.
What is the formula 45 degree elbow?
15.875 x pipe size=
Do you have a formula for pipe cut piece to 90 degree elbow?
Yes, to calculate the length of pipe needed for a 90-degree elbow, you can use the formula: Length = (Distance from the center of the elbow to the center of the next fitting) - (Radius of the elbow). The radius is typically specified by the elbow type (e.g., short or long radius). Additionally, consider any allowances for fitting tolerances when cutting the pipe.
What is the take off for a 8 butt weld elbow?
The take-off for an 8-inch butt weld elbow typically refers to the length of pipe that is required to accommodate the elbow's angle and diameter when calculating pipe runs. For a standard 90-degree elbow, the take-off is generally about 8 inches plus the radius of the elbow, which is typically 10 inches for an 8-inch elbow, resulting in a total take-off of approximately 18 inches. For other angles (like 45 degrees), the take-off measurements would differ accordingly. Always consult specific piping codes or standards for precise measurements.
