0
What is the typical replacement cost of a heating and cooling system for a 3 story 5000 square foot house?
This is contingent upon the zoning you prefer. A house of this size would likely need two to three zones for adequate balancing of the system. Just one HVAC system will not likely accommodate the entire home.
You would likely need two furnaces and two condenser units. Both would need to be sized for the volume of home they condition. The price for this would be approximately $6500 each, or approximately $13,000 total, not including ducting. I am assuming the ducting is existing and in good condition.
In some situations using a light commercial "split system" might work better. A split system sits on the roof and contains both an air mover and a condenser in one unit. It does, however, require a flat roof on which to mount. (Otherwise it looks terrible...)
What else can I help you with?
Are resistor heating affected by line frequency?
No. The heating effect is the product of the square of the current and resistance, where the current is a root-mean-square value.A.C. current is always expressed as a root-mean-square (r.m.s.) value, which is equivalent to a d.c. current which produces exactly the same heating effect. Root-mean-square values are affected by the shape of a waveform, but not by its frequency.
How many pounds of rebar are in a typical concrete slab on grade?
There is no way to answer without a design and the square footage.
What are the operating air pressures of a pneumatic thermostat?
Pneumatic thermostats typically operate at air pressures ranging from 15 to 30 psi (pounds per square inch). This pressure range allows the thermostat to effectively control the flow of compressed air to heating or cooling systems. Proper maintenance and calibration ensure that these devices function optimally within this pressure range.
How many square meter office area can be cooled by 1 ton of refrigeration?
depends on the cooling required ex:-suppose if cooling upto 20c is required the area cooled will be higher as compared to cool upto 15c...........
How many btu to heat 1600 sf?
On average it takes about 1,600 BTUs to heat 50 square feet. Multiplying 50 by 1600 equals about 80,000. Therefore, the heating plan of 1,600 square foot are would take about 80,000 BTUs.
What is the recommended mini split BTU per square foot for efficient cooling and heating in a residential space?
The recommended mini split BTU per square foot for efficient cooling and heating in a residential space is typically around 20-30 BTU per square foot. This can vary depending on factors such as insulation, ceiling height, and climate conditions.
What size heat and air unit to heat and cool a 3000 square foot 2 story home?
It depends on where you live, and the weather / climate there. Additionally a heating & cooling load calculation should be prepared using the ACCA manual J criteria. A good HVAC contractor will do this at no charge as part of the estimate process. For a Rule of thumb, In my town (Salt Lake City, UT) We would likely recommend 20 to 30 Btu's per square foot for heating, and 20 to 25 Btu's of cooling per square foot (for cooling we include footage above grade only- ) For cooling that is one "ton" of cooling for every 600 square feet.
How much will it cost to install central heating and air in a 1400 square foot home?
The cost of installing a central heating unit varies depending on where you live. On average you can expect to pay about $5,000 for a small system capable of cooling a 1,400 square foot home.
How many btu's is needed to heat 1400 square feet?
A 12,000 BTU heater is needed for a 1,400 square foot area. BTU or British Thermal Unit is a unit of measure commonly used for heating and cooling.
How many square feet will Btu's cover?
The coverage of BTUs (British Thermal Units) in terms of square feet depends on the heating or cooling requirements of the space and the efficiency of the heating or cooling system being used. Generally, one BTU can heat or cool about 1 square foot of space in a well-insulated area. However, factors such as ceiling height, insulation quality, and local climate can significantly affect this estimate. It's best to consult with a HVAC professional for a more precise calculation based on specific conditions.
What is the average cost of an electric bill for a 900 square foot apartment?
When I lived in Florida our bill was about $100 in the winter and $200 in the summer for 1000 square feet. We had all electric appliances (kitchen, water heater, washer/dryer, heating/cooling).
How many tons does the air conditioner need to be?
When referring to tons in relation to air conditioning, it is a measure of cooling capacity. A 3 ton air conditioner has the cooling ability of 3 tons of ice. A general rule of thumb for typical construction is 500 square feet of floor space per ton, so a 3 ton unit could cool a 1500 square foot home.
How many Btu per cubic feet home cooling?
Between (.07) and (.24) BTU per cubic foot. For Central Air, might be better to use (.07 BTU per Cu.Ft.) For window AC unit cooling 150 square feet, use (.024 BTU per Cu.Ft.) For window AC unit cooling 1600 square feet, use (.07 BTU per Cu.Ft.) [[[ All scenarios assume 8 foot ceilings ]]]
How many square feet of heating surface is equal to one horse power?
One square foot of heating surface is approximately equivalent to 2.5 to 3 horsepower.
What is the rheem model rrgf-131075ckr tonnage?
The Rheem model RRGF-131075CKR is a 13 SEER (Seasonal Energy Efficiency Ratio) gas furnace and air conditioning unit that has a cooling capacity of approximately 2.5 tons. This tonnage is suitable for cooling spaces of around 1,200 to 1,500 square feet, depending on various factors such as insulation and climate. The unit is designed for efficiency and reliability in residential heating and cooling applications.
What is the importance of room in?
A cooling/ heating unit must supply so many cubic feet of air (CF) per square foot of living space and this air must have a way to vent out of room. All living areas should be ventulated.
Are resistor heating affected by line frequency?
No. The heating effect is the product of the square of the current and resistance, where the current is a root-mean-square value.A.C. current is always expressed as a root-mean-square (r.m.s.) value, which is equivalent to a d.c. current which produces exactly the same heating effect. Root-mean-square values are affected by the shape of a waveform, but not by its frequency.
