0
The load capacity of three 2x10x17' beams depends on several factors, including the type of wood, the spacing between beams, and the load's application (live load vs. dead load). Generally, for typical softwoods, three 2x10 beams can support a combined load of approximately 1,500 to 2,000 pounds when spaced properly and used for floor support. However, it's essential to consult engineering tables or a structural engineer to determine the exact load capacity based on specific conditions and building codes.
What else can I help you with?
What is no load full load?
load in terms of any electrical machine is of 3 types mainly :- 1)resistive load--it means the load connected is a resistor only. 2)inductive load--it means the load applied is an inductor only. 3)capacitive load--it means the load is capacitor only. 4)also there may be combination of all these types or any two of the above loads like capacitive -resistive load;capacitive -inductive load. NO LOAD:--- as it is very clear from the word itself that it is no load that means no load has been applied to the machine..i.e.the output terminal of machine is open circuited FULL LOAD:-- the maximum load value that can be applied to the machine at which it can work without damaging any part of the machine is called machine working at full load ---------mrityunjay pandey (kiit university ,btech 2nd year)
How to install 3 phase heater?
Change over switches have two inputs nd one out put. It is to power the load from two different sources, one a time. Neutral is absent or is given by a bus bar. Off load nd On load are two different types of these switches. Connect two sources or incomer to each of three phases on the primary side (where 6 terminals available) nd load or out comers to secondary. Thats all
What is the maximum load of a grade 2 ladder?
Grade 1 has a max load rating of 250 pounds. Grade 2 has a max load rating of 225 pounds. Grade 3 has a max load rating of 200 pounds.
Would a 50 ohm load and a 100 ohm load connected to a 120 volt supply have the same voltage?
If they're connected one at a time ... first one and then the other ... then each one has 120 voltsacross it while it's connected to the supply.If they're connected across the supply at the same time in parallel, then of course they have thesame voltage across them, because their ends are common.If they're connected across the supply in series, then the voltage across the 50-ohm load is 40 volts,and the voltage across the 100-ohm load is 80 volts.
What is the no load current of a 90kw motor operating 440V 60Hz?
The no-load current of a motor, such as a 90 kW motor operating at 440V and 60Hz, can vary based on its design and efficiency. Typically, the no-load current for such motors ranges from 10% to 30% of the full-load current. To estimate the no-load current, you can use the formula: No-load current ≈ Full load current × (no-load current percentage). The full-load current can be calculated using the formula: Full Load Current (A) = Power (W) / (Voltage (V) × √3 × Power Factor).
How long are radio waves wavelengths?
about 3 meters depending on how load the radeo is.
Why does my sims 3 game take a long time to load?
You might have a lot of custom content installed. I do, it takes my game about 15 minutes to load.
How long does modern combat 3 fallen nation take to load on iPad?
6 million years
How long will a person with HIV and a CD4 count of 617 and Viral Load of 17000 live?
3 days
How long does it usually take for sims to load?
Sims: about 5min. for me Sims 2: about 2-3 minutes for me
How long do you have to wait to put a relaxer in your hair after you have put highlights in?
3-5 weeks
How do you remove excess surface charge from a car battery?
Shake it , put a load tester or a 20 amp charge for 3 min.
How do you install a kill switch on a suzuki lt-r 450?
put a 3 prong -power - load - ground, switch on the (+) side of the coil .....
Show the time 3 hours and 40 minutes later?
put the long hand on the 3 and put the short hand on the 40 by minutes
Can you use 3 amp wire on 0.022 amp transformer?
Yes, as long as the load attached to the wire does not exceed 0.022 amps.
Can 3 phase induction motor start and run rated speed by 2 phase?
yes, It would run as long as the motor was not coupled to a load. Coupled to a load the motor would have no torque and would stall.
How do you make an electric shield?
# get these materials for a 3 x 3 foot shield : 4 metal bars(3 foot),a electric motor and 100 foot of electric wires. # cut a little piece out of the wire each inch. # put the 4 bars together. # put the wire and the bars together. # load up the motor and put it on the wire# put the motor on. # the motor explodes, that means you are stupid
