answersLogoWhite

0

Oil transmits power readily because it is minimally compressible, Lubrication abilities and the cooling properties.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Engineering

What do you need to make a hydraulic arm and how do you make one?

First off, working with hydraulics can be extremely dangerous. With pressures up to 2500 PSI or more, if something is connected incorrectly serious injury or death could occur. Hydraulic systems should only be serviced and/or created by persons with the correct training and experience. Before you can start any building, you will have to decide exactly what you want your hydraulic arm to do. How many limbs will it have? How much weight will it move? A background in basic statics is desirable as you will need to calculate the optimum point on the arm to connect the hydraulic cylinders to to obtain the maximum amount of force from the lever. The basic components that make up a hydraulic system are as follows: -Hydraulic pump (powered by a rotating engine or motor of come kind) -Hydraulic cylinders (this is where your power and motion actually come from) -Hydraulic valves (connected to levers or solenoids to control the flow of hydraulic fluid) -Hydraulic fluid (automatic transmission fluid is very similar and would also work) -Hydraulic fluid reservoir tank (to store fluid that is not currently being used in expanded cylinders) -Hydraulic hoses and fittings to connect everything together And of course the steel or other material for the limbs of the arm itself. Other objects like a pressure gauge or safety valve would be good ideas as well. When selecting these components you need to make sure that -your motor or engine has enough power to run your hydraulic pump -your hydraulic pump has enough power to run your cylinders -your cylinders can produce enough force to accomplish what you need them to accomplish -and that your hoses and valves can handle the amount of pressure your system will be under


How do hydraulic devices make use of fluid pressure?

They direct the energy of the fluid's pressure to utilize that energy. This energy can be used to do anything from operating an electrical switch, to lifting a tractor bucket full or dirt.


Why is hydraulic fluid bad?

Hydraulic fracturing uses low concentrations of chemicals (some hazardous, some not). Usually the maximum concentration of any given chemical is 10-20 gallons per thousand gallons of fracturing fluid. It is true that a poor cement job or hole is the casing can cause water contamination but it is uncommon and current practices make it nearly impossible.


What is hydraulic efficiency?

Hydraulic efficiency is the rate at which a hydraulic consumes gases and liquids to find different ways to make our lifestyles more efficient.


How do you make an easy hydraulic system for a grade 8 student?

Car brake hydraulic system.

Related Questions

What make petroleum oil suitable as hydraulic fluid?

Oil transmits power readily because it is minimally compressible, Lubrication abilities and the cooling properties.


What is a hydraulic drive system?

A hydraulic drive system is a transmission system. This system uses hydraulic fluid that has been pressurized to make a machine work. Most of these systems utilize hydraulic cylinders.


Where do you fill hydraulic fluid in a long 2610 tractor?

To fill the hydraulic fluid in a Long 2610 tractor, locate the hydraulic fluid reservoir, which is typically found near the rear of the tractor. Remove the fill cap, and use a funnel to add the appropriate hydraulic fluid, ensuring you check the fluid level with the dipstick if available. Always refer to the owner's manual for specific fluid type and capacity recommendations. Make sure to check for leaks and properly secure the cap after filling.


What is a system drive?

A hydraulic drive system is a transmission system. This system uses hydraulic fluid that has been pressurized to make a machine work. Most of these systems utilize hydraulic cylinders.


Where do you add hydraulic fluid to a Massey Ferguson 1020 tractor?

To add hydraulic fluid to a Massey Ferguson 1020 tractor, locate the hydraulic fluid reservoir, which is typically found near the rear of the tractor. Remove the cap from the reservoir and use a funnel to pour in the appropriate hydraulic fluid, ensuring you check the fluid level with the dipstick if available. Always refer to the owner's manual for specific fluid type and capacity recommendations. Make sure to avoid overfilling to prevent potential leaks or damage.


Can it hurt the steering pump by putting oil in it?

YES. your power steering pump is a hydraulic pump that pushes fluid through lines to make your wheels move. hydraulic fluid such as ATF or POWER STEERING FLUID is good for your power steering pump. it is a PUMP after all. OIL has the purpose of lubricating, and has very different qualities than hydraulic fluid. DO NOT put OIL in your power steering pump... put POWER STEERING FLUID or if you can't get power steering fluid AUTOMATIC TRANSMISSION FLUID will do...


Air is incorporated in hydrualic system?

No. Air is compressible and fluid is incompressible. So if air is in the hydraulic lines, it will make the fluid act differently; if the fluid is pushing a piston it will be more spongy. Hydraulic fluid(an oil) is usually under high pressure, like 3,000 psi. This causes any small amount of air to go into the solution of the oil. Most Hydraulic Systems return fluid to a reservoir and the reservoir allows the air to "boil out" of solution and is released.


Where to check hydraulic fluid on a 245 Massey Ferguson tractor?

Oh, dude, checking the hydraulic fluid on a 245 Massey Ferguson tractor is like finding the last slice of pizza at a party - it's crucial! You'll usually find the hydraulic fluid dipstick near the back of the tractor, close to where the hydraulic pump is located. Just make sure the tractor is on a level surface, pull out the dipstick, wipe it clean, reinsert it, and then check the fluid level. Easy peasy, lemon squeezy!


Why might pump be needed in a hydraulic system?

it provides the actual fluid pressure to make the whole system work


How do you add hydraulic fluid for a 2001 convertible top could this be the reason my top goes down ok but has a very hard time to go back up?

Well I today anwsered my own question all it needed was hydraulic fluid. In the back of the convertible there should be a black rubber plug all you do is get any type of hydraulic fluid( make sure the hydraulic fluid in the back says mixs with any hdraulic fluid) you pour it in the cylinder shape in were you took out rubber plug make sure it over flows and plug it back in and your done your top should now go up way faster, smother,and nice.


How much hydraulic fluid in a 1991 tractor?

What's the make (manufacturer) and model? That information will be pertinent before this question can be answered.


What happens if you put transmission fluid where the power steering fluid goes?

Basically.................price!!! It's safe to use Trans Fluid for Power Steering Fluid, they are both hydraulic oil/fluids.........but make sure to check your owners manual.