answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

To prevent fuel damage decay heat must be removed from the reactor core?

after the reactor shuts down


What precaution should be taken when working with current transformer that is in service?

Its secondary must never be open circuited. If its burden is to be removed, then the secondary must be short circuited first, and removed only after the burden is replaced.


What Parts and function of safety valve of boiler?

If the pressure in a steam boiler exceeds a set limit, a safety valve is provided that will open to relieve the pressure. This prevents a boiler explosion. When the pressure is being relieved in this way, very hot steam will be release from the valve. The hot steam is extremely dangerous to people, therefore a discharge is provided. This is a pipe or other means of directing the hot steam to a release point outside, away from where people are likely to be.


How does the ti plasmid make genetic engineering plants a possibility?

It is capable of introducing exogenous genes into plant genomes. T-DNA genes are removed from the Ti plasmid and are replaced with the gene of interest.


Why are nuclear power stations bad?

Strictly speaking, nuclear power stations aren't really that bad, since every method of getting energy has pros and cons. The disadvantages of nuclear power stations are that they create some waste products. These things are radioactive and waste with high radiation output (over 90% of waste does not emit more radiation than a cup of coffee) will cause long term damage to anyone staying near it for awhile. Around 90% of the available energy in the fuel rods when they are removed from the reactor after three fuel cycles (the typical period). If the highly radioactive fission fragments were extracted and the fissionable material reprocessed into new fuel (as they have been doing in France for decades), the remaining volume of radioactive material would be significantly reduced. Another disadvantage is that nuclear power stations may melt down, irradiating the land around them. There is actually a low chance of a meltdown, but when it does happen, an entire region can be contaminated and poisoned.

Related Questions

What is a nuclear reactor meltdown?

A nuclear meltdown is an informal term for a severe nuclear reactor accident that results in core damage from overheating. A meltdown occurs when the heat generated by a nuclear reactor exceeds the heat removed by the cooling systems to the point which at least one nuclear fuel plate exceeds its melting point.


How long does it take a nuclear reactor rod to cool down?

It can take anywhere from several years to several decades for a nuclear reactor rod to cool down to a level where it can be safely removed from the reactor core and stored. Cooling times vary depending on the type of reactor and the specific isotopes present in the fuel rod.


What is a used fuel in nuclear power plants?

The used fuel in a nuclear power plant is the nuclear fuel being discharged from the nuclear reactor after being irradiated during reactor operation. It is usually composed of trans-uranium heavy elements, a wide variety of fission products (that resulted from the nuclear fission processes in the nuclear reactor) and products of radioactive decay (produced before and after fuel discharge from the nuclear reactor).


If the control rods in a nuclear reactor are removed would the condition be supercritical or subcritical?

If the control rods in a nuclear reactor were somehow to be instantly "jerked" out of the reactor, the reactor would go supercritical. If they were pulled at a normal rate and all of the control rods were pulled out, the reactor would start up and heat up and would end up running far too hot. Any one of several safety systems would shut the reactor down before this could happen. If the safety systems were disabled, the reactor would overheat and a meltdown may occur.


What is the difference between nuclear power plant and nuclear reactor?

It's really just a matter of degree, all reactors produce some power. Those used in a power plant will produce perhaps 3000 to 5000 Megawatts thermal. Low power reactors producing a few kilowatts are used for experiments, teaching in universities, and for producing radioisotopes by irradiating samples, but reactors in this sort of power level would not be harnessed to produce electricity, the heat produced if large enough would be removed and rejected to the atmosphere or to a water cooling circuit. This makes them simple to operate and to start and stop as required.


To prevent fuel damage decay heat must be removed from the reactor core?

after the reactor shuts down


Why is a nuclear reactor dangerous?

Components in the reactor inside the primary shielding will be radioactive, even after all the fuel has been removed. Provided everything is monitored and assessed properly and health physics advice followed by the operators, there should be no need for anyone to be exposed to dangerous levels during decommissioning.


Where does nuclear waste go from a nuclear submarine?

In the United States, when a nuclear submarine has "run out of" nuclear fuel for its reactor (this takes many years), the reactor may be opened, and the spent fuel sent for reprocessing at the Naval Reactors facility at the Idaho National Laboratory. The reactor's core may then be refueled. This process can take some time, and handling the spent fuel is dangerous and requires complex procedures to prevent contamination. If the submarine is to be overhauled, or retired, the fuel is removed for reprocessing, and the reactor compartment is cut out of the submarine, sealed, and moved for disposal to the Department of Energy's Hanford Nuclear Reservation in Washington State, where they are kept in dry storage. The submarine may be welded back together, or the sections floated, until a new compartment and reactor are installed, or the vessel is cut up for scrap. Low level radioactive waste may be handled in other ways.


In a nuclear power plant excess heat is?

In a nuclear power plant, excess heat is typically removed using a cooling system, such as water or gas, to prevent overheating of the reactor core. This excess heat is generated from the nuclear fission process that occurs within the reactor. Proper heat removal is essential to maintain safe and stable operation of the nuclear power plant.


What is the composition control rods at nuclear power plants?

Control rods at nuclear power plants are typically made of materials that absorb neutrons, such as boron or cadmium. These rods are inserted or removed from the reactor core to control the rate of the nuclear fission reaction by absorbing or slowing down neutrons. This allows operators to adjust the power output of the reactor.


How do they start a nuclear reactor?

With all control rods inserted all the way, begin inserting fuel rods.When the basic minimum operating number of fuel rods have been inserted, insert a continuous neutron source of known intensity.Measure the neutron flux in the reactor and calculate the reactor's neutron multiplication factor to determine how close you are to design predicted critical.Begin withdrawing control rods very slowly, stopping periodically and repeating step 3. Each time the neutron multiplication factor should increase.If the multiplication factor keeps increasing in step 4 while the control rods are stopped, you have reached critical. Remove the neutron source and the neutron flux in the reactor should decline slightly then become constant.You have now safely started your nuclear reactor. Congratulations!If anything unexpected happens reinsert all control rods, remove the neutron source, find and fix the problem, and restart the procedure.


What is the pattern for a nether reactor core in minecraft?

The nether core reactor has been removed and no longer has a pattern in newer versions.