0
What should be the Lap length when two different dia bars overlap with each other?
The lap length when two different diameter bars overlap should generally be at least 40 times the diameter of the smaller bar for tension members and 50 times the diameter for compression members. This ensures adequate bonding and structural integrity. However, specific requirements can vary based on design codes and project specifications, so it's important to consult the relevant guidelines for precise calculations.
What else can I help you with?
Why do only parts of the thread appear sharp and clear at any given time?
Because the thread overlap each other.
What is a teardrop in computer terms?
A DoS attack where fragmented packets are forged to overlap each other when the receiving host tries to reassemble them.
Why second and third angle projections not used in orthographic projections?
because 2nd and 4th angle projection overlap each other
What circumstances combined footing is required?
where there the two columns faces overlap each other, when the column face is near to the boundary line
Two resisters have the same resistance but different cross sectional area what is difference?
If two resistors of have same value but different in shape or cross sectional area, as you said so. Then the difference may be the length of the other resistor. In short, one resistors cross sectional area is wide and other is lenghty.
What is the length of the bottom chord of a truss?
The same legnth as the distance the outer walls are from each other plus the overlap.
What is Development length for steel bars?
Lap length is the length overlap of bars tied to extend the reinforcement length.. Lap length about 50 times the diameter of the bar is considered safe. Laps of neighboring bar lengths should be staggered and should not be provided at one level/line. At one cross section, a maximum of 50% bars should be lapped.In case, required lap length is not available at junction because of space and other constraints, bars can be joined with couplers or welded (with correct choice of method of welding).
You want to know how to calculate the square meters?
If its for a rectangle, multiply length x width. Other figures have different formulae.If its for a rectangle, multiply length x width. Other figures have different formulae.If its for a rectangle, multiply length x width. Other figures have different formulae.If its for a rectangle, multiply length x width. Other figures have different formulae.
What is ment by subnet?
It means that a larger network has been divided into smaller networks, called "subnets". Each subnet has its own range of IP addresses, that should not overlap with the other subnets.It means that a larger network has been divided into smaller networks, called "subnets". Each subnet has its own range of IP addresses, that should not overlap with the other subnets.It means that a larger network has been divided into smaller networks, called "subnets". Each subnet has its own range of IP addresses, that should not overlap with the other subnets.It means that a larger network has been divided into smaller networks, called "subnets". Each subnet has its own range of IP addresses, that should not overlap with the other subnets.
How do you replace the floor in a 1987 Pontiac trans am Should it be rivited or welded in What type of welding is best Should the new floor overlap the old floor Other information would be appreciate?
The old floor should be cut out. Preferably with a plasma cutter. The new floor should be welded in. It would probably be best to leave some overlap, flange it and then spot or rosette weld the new floor to the overlap flanges.
What is an interaction of various different waves called?
When different waves overlap and combine, it is called interference. Interference can result in constructive interference, where the waves amplify each other, or destructive interference, where they cancel each other out.
How are isosceles and scalene different?
An isosceles triangle has two sides that are equal length, and the other side would be a different length. A right triangle could be an isosceles triangle. On the other hand, a scalene triangle has all of its sides different lengths.
Interference is a condition that occurs when .?
Interference occurs when two or more waves overlap and interact with each other, causing a change in their amplitudes or frequencies. This interference can be constructive, where the waves reinforce each other, or destructive, where they cancel each other out. The resulting interference pattern depends on the relative phases of the waves at the point of overlap.
How are fishes scales arranged?
they overlap onto each other
How does synthetic aperture radar different from other radar?
Synthetic Aperture Radar synthesis a longer antenna (or Aperture) by integrating pulses together that overlap each other to exploit turn rate phenomena.
What is isorhythmic overlap?
Isorhythmic overlap is a compositional technique in music where two different rhythms, typically a repeating pattern in the melody (color) and a repeating pattern in the harmony (talea), are combined or layered on top of each other. This creates a complex and interwoven texture that adds richness and depth to the music.
What is a overlap pool liner?
Overlap refers to just that... the liner overlaps the top of the pool. The other option is a hung liner, where the liner locks into a track..
