0
If you had to ask this question here you need to learn more about your local wiring code re all the items you must use for this new motor circuit.
So that the new installation is safe and legal - and complies with the terms of your home or business insurance policy - you must use the correct type and size of cable, the correct type of circuit breaker and the correct type of wall outlet.
Serious home fires can result from incorrectly-installed new circuits.
Another answer
NEC table 430.248 lists this motor as drawing 17 amps, !7 x 1.25 =21.5 amps. Number 10 copper wire.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS
What else can I help you with?
What are the procedures for the connection of single and 3 phase circuits?
Single phase connection has 1 phase wire and a neutral wire. Another wire for protective earth. In three phase system, motor can be connected in star or delta. Most AC induction motors are in Delta. Power distribution system is generally 3 phase 4 wire. Transmission system is 3 phase high voltage. Industry uses 3 phase system, where as 1 phase is for domestic, commercial applications. Both 1 and 3 phase system has a frequency. It is either 50 Hz or 60 Hz, depending upon the country or region.
What size of circuit breaker do you use for 25amperes induction motor?
Read the specification plate on the motor to determine the amount of current that the motor uses, as well as the voltage and phase. Most likely, it will be a 3 phase motor, so you can't simply connect it to your house wiring, but without sufficient information, it is impossible to tell you all of the specifics. <<>> The code book rates the amperage of a three phase 40 HP motor by different voltages. at 200 volts - 120 amps, 230 volts - 104 amps, 460 volts - 52 amps and 575 volts - 52 amps. A breaker for a motor has to be sized to 250% of the motors full load amps. Also the wire size for a motor has to be 125% of the motor full load amps.
What is RPM of a 2 pole single phase motor?
3600 rpm 120x60/2=3600 where 120 is given 60 cycle 2 pole
How star delta helping motor from overheat?
star delta motors start as a Y for 3 phase so the windings that normally see 480 volts see 277V a relay switches to delta then it runs as a normal delta motor the reduces the starting current by about 60% for 3 phase
Can you run a 460 volt 3 phase 60 hertz refrigeration compressor on 460 volt 3 phase 50 hertz?
Possibly. You need to check the rating on the device. Many compressors can operate on either 50 or 60 Hz.
What is the recommended wire size for a 60 amp circuit?
The recommended wire size for a 60 amp circuit is typically 6-gauge wire.
What is the appropriate wire size for a 60 amp circuit?
The appropriate wire size for a 60 amp circuit is typically 6-gauge wire.
What is the recommended wire size for a 60 amp breaker?
The recommended wire size for a 60 amp breaker is typically 6-gauge wire.
Minimum breaker size 60 horsepower motor?
A 60 horsepower motor typically requires a minimum breaker size of 100 Amps for normal operation. It is important to consult the motor's specifications or a licensed electrician to ensure the correct breaker size for safe and efficient operation.
What is the recommended wire size for a 60 amp service?
The recommended wire size for a 60 amp service is typically 6-gauge copper wire.
What is the appropriate wire size for a circuit requiring 60 amps?
The appropriate wire size for a circuit requiring 60 amps is typically 6-gauge wire.
What is the recommended wire size for a 60 amp 220v circuit?
The recommended wire size for a 60 amp 220v circuit is typically 6-gauge wire.
What is the recommended copper wire size for a 60 amp circuit?
For a 60 amp circuit, the recommended copper wire size is typically 6 AWG (American Wire Gauge).
What is the recommended wire size for a 60 amp copper circuit?
The recommended wire size for a 60 amp copper circuit is typically 6 AWG (American Wire Gauge).
What is the appropriate wire gauge size for a 60 amp circuit?
The appropriate wire gauge size for a 60 amp circuit is typically 6 AWG (American Wire Gauge).
What information can I find in the 60 amp wire size chart?
The 60 amp wire size chart provides information on the appropriate wire gauge or size to use for a 60 amp electrical circuit. It includes details such as the wire gauge, maximum current capacity, and insulation type suitable for a 60 amp load.
What is the recommended wire size for a 60 amp Tesla charger installation?
The recommended wire size for a 60 amp Tesla charger installation is typically 6 AWG copper wire.
