In occupancies required to be equipped with a fire alarm system, theback-flowpreventer valves shall be electrically supervised by a tamper switch installed in accordance with NFPA 72 and separately annunciated.
mess with it
An egg. The tamper proof seal.
It can and it is Although U-238 is not very radioactive -- it's sometimes called depleted Uranium -- it is used as a "tamper" in the core of nuclear warhead. Its use as a tamper greatly increases the yield energy of the device. Wikipedia has a pretty good article to check out. Uranium 238 is not fissionable with thermal neutrons; uranium 238 cannot be used in bombs as fissionable, explosive material.However as the final stage tamper of a hydrogen bomb the high energy fusion neutrons will fission Uranium-238, possibly generating 90% of the yield and a corresponding amount of the fallout of such bombs.
It sounds like you are trying to steal power. I don't recommend it; modern energy meters are pretty well tamper proof.
In Great Britian, when track is being laided, there is a track machine used to "tamper" the track so they are straight and parallel to each other.
The Tamper switches for a fire sprinkler system are located on the main control valves which are located on either side of the backflow preventer for a wet type automatic fire sprinkler system. These switches are wired into the monitoring control system/alarm panel to ensure the valves remain open at all times (or not tampered with.) If the tamper switches are used they will show a supervisory trouble on the panel so the monitoring company or business will know there system is out of service.
The function of a water flow switch is to detect water flow in the sprinkler system, usually during a fire event, to signal a local electrical fire alarm, or fire alarm panel to activate the alarm devices in the building,and send an alarm signal to a central station or alarm company to alert the fire department.
A tamper switch is a security feature used in alarm systems or access control systems to detect if the device or equipment has been tampered with or removed from its designated location. When triggered, the tamper switch sends a signal to the control panel to alert of a possible breach or tampering attempt.
A tamper switch (in a burglar alarm system for example) is designed to stop un-authorised access to the inside of the control panel. It usually takes the form of a small micro-switch that activated when the cover is opened. Even if the alarm has been de-activated (by entering the correct code) the anti-tamper circuit is still active so long as there is power to the system. Cutting the lead to the external sounder, or the mains lead doesn't stop it either - there is usually an internal sounder, and a back-up battery.
# Disconnect and isolate the battery negative cable. # If the vehicle is so equipped, remove the tilt steering column lever. # Remove both the upper and lower shrouds from the steering column # Remove the lower fixed column shroud. # Move the upper fixed column shroud far enough to access the rear of the multi-function switch # Remove the tamper proof mounting screws (a Snap On tamper proof torx bit TTXR20B2 or equivalent is required) that secure the multi-function switch to the steering column. # Gently pull the switch away from the steering column far enough to access and remove the multi-function switch wire harness connector screw. # Unplug the wire harness connector from the multi-function switch. # Reverse the removal procedures to install. Tighten the fasteners as follows: #* Multi-function switch wire harness connector screw - 2 N·m (17 in. lbs.) #* Multi-function switch mounting screws - 2 N·m (17 in. lbs.)
Tamper proof means it is not possible to tamper with something. Tamper evident relates to devices that reveal if something was tampered with.
First you locate the source of the alarm, undo the condition (e.g., valve closed, inadequate pressure, etc), then reset the alarm condition on the sprinkler control panel and reset the alarm on the fire alarm control panel (assuming they're connected, as required by many fire codes).
It depends on your State, but generally the only thing that's illegal to disable is the cutoff switch. In some States, it may be illegal to tamper with the engine RPM governor or exhaust system.
All the info I have gotten from the dealership is that if you do tamper with the cats but do a dual exiting system then you will not void your warranty.
it is were you tamper with the system and you get colourful custum classes and a colourful clan tag etc.
The past tense of tamper is tampered.
Anything which is tamper proof cannot be altered, changed or messed about with.