R (resistance) and C (capacitance).
Timer1 Timer2 Done Timing ---|/|---------|/|---------[Timer On - Timer 1]--- Timer2 Timer1 Done Timing ---|/|---------|/|---------[Timer On - Timer 2]--- Timer1 Timing Flash --| |--------------------( )------- Adjust the preset time for timer1 to change your "flash on" duration. Adjust the preset time for timer2 to change your "flash off" duration.
The Z1 component in the circuit diagram of the LEDTEC timer IT-88 model typically refers to a Zener diode. It is used for voltage regulation, ensuring that the voltage across certain parts of the circuit remains constant despite variations in input voltage. This stabilizes the operation of the timer and protects sensitive components from voltage spikes. Proper functioning of Z1 is crucial for the reliable performance of the timer.
UJT is an abbreviation for (Unijunction Transistor) the electronic component that is at the heart of a simple timing circuit. A UJT timer is a circuit used in an electonic system to deliver a specific time. For instance, a 30 second UJT timer might be used to turn on a Green traffic signal for 30 seconds, then turn off. UJT is a specifically cheap way of doing this type of timed signal. Timers using UJTs have largely be superseded by timers based on a 555 integrated circuit.
an oscillating RC circuit
The 555 timer IC is a device that can create various kinds of time delays in a circuit. It uses a threshold pin that is typically connected to an RC circuit. Depending on how it is connected, it can operate in one shot mode (monostable), astable mode (retriggerable), or schmitt trigger mode.
The 555 IC is a universal timer circuit. Via the addition of external components (resistors, capacitors) the designer can generate various timing waveforms.
LM555 is a timer it can be used for many applications not only oscillators. the timing can be setup from microseconds to hours by the right choice of external passive components. Timing is set precisely by laser controlling a voltage divider as .639. So while the chip is precise the external components are not. but that is used to begin a design.
Timer1 Timer2 Done Timing ---|/|---------|/|---------[Timer On - Timer 1]--- Timer2 Timer1 Done Timing ---|/|---------|/|---------[Timer On - Timer 2]--- Timer1 Timing Flash --| |--------------------( )------- Adjust the preset time for timer1 to change your "flash on" duration. Adjust the preset time for timer2 to change your "flash off" duration.
Timer relays are used in control circuitry. There are two main types, an (off delay) and an (on delay). If you want one device to turn off before the timer controlled device then you would use an off delay timer. If you want one device to turn on before the timer controlled device then you would use an on delay timer. When the timer is energized this starts the timer circuit in the relay to time out.
The Z1 component in the circuit diagram of the LEDTEC timer IT-88 model typically refers to a Zener diode. It is used for voltage regulation, ensuring that the voltage across certain parts of the circuit remains constant despite variations in input voltage. This stabilizes the operation of the timer and protects sensitive components from voltage spikes. Proper functioning of Z1 is crucial for the reliable performance of the timer.
IC 555 is a simple timer integrated circuit device and used for traffic light timing to control traffic flow.
Because the timing is set by the time constant of a resistor and a capacitor. With R in ohms and C in Farads, the time-constant is RC in seconds. If the capacitor leaks the timing will be wrong.
The outlet would be the more often recommended place for it.An electrical timer can be placed anywhere within the circuit. Usually the timer would be placed at the front end of the circuit.
The timer will have terminals associated with it. They may be on a relay socket that the relay plugs into. There will be two terminals used to bring the supply voltage to the relay timer. The load will be connected in series to either an open or closed set of contacts on the relay. The load voltage is controlled by the timer relay.The operation is, when the timer relay coil is energized the timing circuit in the relay is energized. This starts counting down until the time set point is reached and then the contacts either open or close depending on what set of contacts that you connected the load to.Some timer relays need to have the timer coil circuit de energized to reset the timing relay, others use a separate input voltage terminal on the relay to reset it without having to de energize the whole relay.
UJT is an abbreviation for (Unijunction Transistor) the electronic component that is at the heart of a simple timing circuit. A UJT timer is a circuit used in an electonic system to deliver a specific time. For instance, a 30 second UJT timer might be used to turn on a Green traffic signal for 30 seconds, then turn off. UJT is a specifically cheap way of doing this type of timed signal. Timers using UJTs have largely be superseded by timers based on a 555 integrated circuit.
an oscillating RC circuit
It sounds to me like the exhaust timer is just a switch. The 20 amp rating that the timer is given is the maximum amount of current that it can handle and still be within its safety specifications. It will work very well on a 15 amp circuit.