0
What else can I help you with?
What is a DISS fitting?
Diameter Index Safety System, a way to ensure that one type of gas fitting will only connect to appropriate hoses, tubing and devices.
Makeup gas compressor spill back valve function?
It is a quick response valve, which opens fully in 1.5-2 seconds. basically will be of fail open type. Its opening depends on the surge control.
What is the maximum gpm through half inch copper pipe at 25 psi?
When you say 1/2" are you talking about 5/8 OD or nominal size and which type of copper? K /L/ M as there is friction looses to consider I am referring to 1/2" nominal type L copper pipe, and the friction loss is negligent because the section of 1/2 inch tubing is only 2" nipples on either side of a electric shut off valve. The actual set-up is 1" PVC supply at 65psi, reduction fitting to 3/4" into a pressure redusing valve, 3/4" out of the valve through another reduction fitting to 1/2" into and through the shut-off valve, then into the furnace. Distance from the first 1' to 3/4" reducer to the furnace is only a distance of about 14". Hope this helps.
What is the difference between a globe valve and a ball valve?
The Globe valves are generally used to control the flow rate and ball valve used for open /close purpose only.A globe valve is a type of valve used for regulating flow in a pipeline, consisting of a movable disk-type element and a stationary ring seat in a generally spherical body.A ball valve is a valve with a spherical disc, the part of the valve which controls the flow through it.
Which valve is prefered to use for ammonia tanks a globe valve or a gate valve?
If the purpose of the valve is to modulate flow, a globe valve is preferable. If the valve is only on-off, a gate valve is preferable because of lower pressure drop when the valve is open. As wikipedia , A globe valve is a type of valve used for regulating flow in a pipeline, consisting of a movable disk-type element and a stationary ring seat in a generally spherical body. So i think it is a globe valve to use in steam pipeline.
How do you connect copper propane pipe and shutoff valve?
To connect a copper propane pipe to a shutoff valve, you will need to use a threaded fitting that matches the size and type of the pipe and valve. Apply pipe dope or Teflon tape to the threads before connecting them. Tighten the fitting securely using a wrench or pliers to create a leak-proof connection.
What type of fitting is required to connect a refrigerator water line to the water supply?
A compression fitting is typically required to connect a refrigerator water line to the water supply.
What type of fitting do you use to connect PVC pipe to unthreaded galvanized pipe?
You can't. There is no fitting to do this. Galvanized has to be threaded.
How can I connect PEX tubing to a water heater?
To connect PEX tubing to a water heater, you can use a fitting called a PEX fitting. This fitting is designed to connect the PEX tubing to the water heater securely. Simply insert the PEX tubing into the fitting and use a crimping tool to secure it in place. Make sure to follow the manufacturer's instructions for the specific type of PEX fitting you are using.
Where is the fuel filter located on a 1996 Chevy Cavalier?
Follow the fuel line from the engine toward the rear of the car and you will find it. the fuel filter is located under the vehicle between the fuel tank and the EVAP canister. the inlet fitting is a conventional tube nut on the end of the inlet line the outlet fitting is a quick connect type fitting.
How do you define the coefficient of incipient cavitation?
The cavitaion index across a valve or pipe fitting is defined as the ratio of difference between upstream pressure and vapor pressure to the pressure drop across the valve or fitting. The index at which incipient cavitation, damage, or choked flow occurs is based on testing and depends on the type of valve or fitting.
What is a DISS fitting?
Diameter Index Safety System, a way to ensure that one type of gas fitting will only connect to appropriate hoses, tubing and devices.
Where do you add freon to your 2001 Ford Focus?
R 134A freon is added into the "quick connect type" fiiting, located on top of the AC accumulator, which is located underneath the front of the passenger side fenderwell. First, raise the car with your jack placed behind the front tire. Then remove three screws that secure the black plastic fenderwell cover. One screw has a torx head and is located at the front lower edge of the fender. The other two are Phillips head plastic screws located in front of the strut. With the three cover screws removed, pull down the front portion of the fenderwell cover. This will expose the AC accumulator, which looks like a quart sized aluminun can. Now, unscrew the valve cover from the quick connect fitting and connect your AC recharging hose to the fitting. By the way, it pushes on and snaps onto the fitting. Now, follow the instructions that came with your AC recharge kit, for the dtermining the corrct amount of freon to add. Finally, replace the fitting valve cover, the fenderwell cover/screws and your done.
Is the fitting indicated by the arrow shall be a what kind of tee?
The fitting indicated by the arrow is likely referring to a specific type of tee fitting, such as a "branch tee" or "reducing tee." A branch tee is used to connect a branch line to the main line, while a reducing tee is designed to connect pipes of different diameters. The exact type can depend on the context and application.
What does aro stand for in an aro series pneumatic fitting?
In the context of an ARO series pneumatic fitting, "ARO" stands for "Air Research Organization." This designation typically refers to a specific type of quick-disconnect fitting used in pneumatic systems for air and fluid transfer. ARO fittings are known for their durability and ease of use, often featuring a push-to-connect design that facilitates rapid connections and disconnections in industrial applications.
How can I connect PEX tubing to a hot water heater?
To connect PEX tubing to a hot water heater, you will need to use a fitting called a PEX fitting. This fitting can be crimped onto the PEX tubing using a crimping tool. Make sure to follow the manufacturer's instructions for the specific type of PEX fitting you are using. Once the fitting is securely attached to the tubing, you can then connect it to the hot water heater using the appropriate connectors. Be sure to check for any leaks before turning on the hot water heater.
What is a sweat inlet?
It is probably referring to the type of fitting. A fitting that is soldered to a copper pipe. It is called sweating when you use solder and a torch to connect copper pipe together or attach fittings to copper pipe.
