0
What else can I help you with?
What is time delay valve?
time delay valve is nothing but when a certain pressure is reached the valve will actuate it when the delay reaches
What is the difference between an air bleed valve and a pressure relief valve on a boiler?
They serve two different purposes. An air bleed valve is used to remove air from the circulation system. A pressure relief valve is designed to automatically open when certain pressure levels are reached.
What is safety valve?
It is a device that opens on its own if a certain condition is reached. Let's say you are designing a water heater. You know if everything goes wrong the unit could reach 210 degrees F, or to have 150psi pressure inside it. You also know if either of those things happen the water heater could explode...so you put a safety valve on it that opens if either condition is reached.
What is A well in which water rises because of pressure within an aquifer?
They are called Artesian Wells where underground water under positive pressure causes the water level in the well to rise to a point where hydrostatic equilibrium has been reached. If the water reaches ground level they are call flowing artesian wells; some my look like fountains.
What is the ratio of latching current to holding current?
Latching current is the current flowing between anode to Cathode when thyristor is turned on using gate pulse. If the gate pulse is removed before the required min amount of latching current value is not reached thyristor will turn off. To keep the thyristor in on state the gate pulse duration should be so adjusted that the min latching current value is reached before it ends.
How long does it take to pressure can applesauce?
Pressure canning applesauce typically takes about 20-25 minutes once the canner has reached the required pressure level.
What is the function of compressor governor?
It puts the compressor into an unload state once cut out pressure is reached, and back into a loaded state once the cut in pressure is reached. Depending on the exact setup, a line from one of your air tanks will go to your governor. When the cut out pressure (between 120 and 135 psi) is reached, a valve opens in the governor to send air to to compressor and to the air drier. This closes the discharge valve on the compressor, sending it into an unloaded state, and also starts the air drier purge cycle.
When vapor pressure equals atmospheric pressure at the surface of a liquid it has reached its what?
When the vapor pressure equals atmospheric pressure at the surface of a liquid, it has reached its boiling point. This is the temperature at which the vapor pressure of the liquid is equal to the pressure exerted on it by the surrounding atmosphere, causing the liquid to change into vapor.
How do I know when I've reached the right cooker pressure?
You can know when you have reached the right cooker pressure by checking the temperature gauge. The right temperature would also depend on what you are cooking.
How much pressure will compressed CO2 create when released in an air cylinder?
Whatever amount of pressure was used to compress the CO2 originally, can be reached (or nearly reached) when it is released into an air cylinder.
How do you adjust a pressure regulator?
To adjust a pressure regulator, turn the adjustment screw clockwise to increase pressure or counterclockwise to decrease pressure until desired pressure is reached.
What is the closing force of a gas regulators?
The closing force of a gas regulator is the force exerted by the spring-loaded diaphragm to close the valve and prevent gas flow when the set pressure is reached or exceeded. This force is designed to be strong enough to maintain pressure control within the desired range and prevent gas leakage.
What is an example of critical in a sentence?
The patient's blood pressure had reached critical levels.
The highest temperature reached inside the pressure cooker will depend upon the?
The highest temperature reached inside a pressure cooker will depend on the pressure level set for cooking. As pressure builds up, the boiling point of water increases, allowing food to cook at higher temperatures than under normal atmospheric conditions.
How can I properly adjust a pressure regulator to ensure optimal performance?
To properly adjust a pressure regulator for optimal performance, follow these steps: Start by identifying the desired pressure range for your system. Use a pressure gauge to measure the current pressure and compare it to the desired range. Adjust the regulator knob in small increments to increase or decrease the pressure. Monitor the pressure gauge while making adjustments until the desired pressure is reached. Test the system to ensure it is functioning properly at the adjusted pressure. Make any necessary fine-tuning adjustments to maintain optimal performance.
Why does a 2000 Chevrolet Suburban pump run when vehicle is turned off?
I am not sure about a 2000 Chevy Suburban specifically, but if you are referring to an electronic fuel pump, it is possible an in-line pressure sensor may keep a charge on the pump until the fuel line has whatever the minimal pressure is required to ensure ignition the next time you start the vehicle... Once the required pressure is reached, the pump will shut off automatically. If it does not shut off at all, it could be a leak in the fuel line at some point.
What happens as the drive shaft rotates on a Stratopower pump?
It is essentially a variable displacement pump. At low pressure, the sleeve, driven by a spider that is attached to the compensator piston seals the relief holes in the piston to provide positive pressure to the discharge port. When the required pressure is reached, the compensator piston moves the spider to uncover the relief holes from the sleeve. Thus not pressure can be built up in the piston. This results in the pump being off-loaded.
