=== === === ===
Waste and storm and water less then $87,000
4500 to 9000 is to be expected
Depends. A repipe simply means that your current pipe supply lines have a problem that needs to be addressed. Do copper pipes need to be replaced, sometimes, especially if they are installed incorrectly, or if you have a highly corrosive water quality in your area. A good water system would include water treatment, and pressure regulators with the correct type of piping to ensure that the water pipe last for the longest possible period. I have seen copper repipes last 20 plus years with no problems and some only 1 year because of poor installation practices.
To repipe a house with PEX, first turn off the water supply and drain the pipes. Cut out the old pipes and fittings. Measure and cut the PEX tubing to fit the new layout. Install fittings and connectors as needed. Secure the PEX tubing in place using clips or straps. Turn on the water supply and check for leaks. Flush the system to remove any debris.
=That would depend on the diameter of the tubing and the type K,L,M, DWV. ACR or TP and the run and location Above ground ceiling level or is it under ground where trenching and shoring is involved, Who is doing the insulation?=Then how long is the job going to take with the installation of compatible clevis hangers and copper coated riser clamps and are the joints MJ / Soldered / Brazed ?Are you asking about licensed Masters or Journeymen doing the installation or Fly by nights with no formal training?
DON'T re-pipe a home using PVC. -Use PEX instead, cheaper, better quality and easier to install.
You could use the site Yellowpages to look for a company that can re-pipe your kitchen and that is also located near your area. Or, depending on where you live there are several websites with information about re-piping kitchens.
To repipe your house using PEX piping, you will need to first shut off the water supply and drain the existing pipes. Next, plan the layout of the new PEX piping system and measure and cut the PEX tubing to fit. Install fittings and connectors as needed, and secure the PEX tubing in place using clamps or brackets. Finally, test the new piping system for leaks before turning the water supply back on. It is recommended to consult a professional plumber for guidance and assistance with repiping your house using PEX piping.
Repiping the supply lines involves the replacement of the old existing water lines with new pipes. The need to repipe occurs when old lines become clogged or begin to show signs they are about to leak. Those signs include rust on the outside of the pipes, sweating and water calcification (a white or greenish residue) plus low water flow and rusty or discolored water. Repiping today is done primarily with PEX (Poly Ethylene with X-Linked molecules). Some people still use copper though the expense for materials and labor make PEX a much more popular choice. Though other materials like galvanized pipe and CPVC are legal to use they should be avoided due to their inherent problems; namely rust in galvanized and high failure rates in CPVC. Old supply lines are not necessarily followed during a repipe. Often, lines are covered by concrete or run in such a way to make it impractical. An experienced repiper is more than just a plumber. The repiper will run lines where it makes the most sense and does the least amount of damage. There is almost never a reason to cut concrete when replacing supply lines. A repipe should not only include the 'horizontal' lines under the floor, it should include all lines to the existing fixtures. This includes the 'vertical' lines in the walls as well as the supply lines from the angle stop shut offs right up to the existing fixtures. Water can do an amazing amount of damage in a very short time and leaks in the walls or under sinks are usually the most dangerous. A proper repipe starts at the connection in the basement or crawl space. Here, a connection is made to the main line coming into the house from the meter. It is often important to do the main line at the same time as the rest of the house. This can be accomplished in most cases with a directional bore that leaves your landscaping and concrete neat, clean and undisturbed. Once the connection is made, a shut-off is installed and new trunk lines are run throughout the house. From there the vertical pipes can be run up through the same holes and back into the walls or you may chose a deck mount which is drilled from below into a cabinet or behind a washing machine. In the case of the deck mount, the pipes are mounted outside the wall but hidden beneath the cabinet or behind the washer. This saves having to patch the walls again after the job is done.
Mandatory Essentials 1-License #, and in good standing? 2-Liability insurance. Get amount insured, and copy of policy. 3-Workers comp. Get policy copy 4-Written Guarantee 5-Written upfront price 6-City inspection/permit If you dont get these essentials upfront, you are only taking a gamble on what kind of experience you may have. Additional items i provide to my clients are listed below. - employee background checks/substance and criminal -uniforms -time schedule -warranties,for repipe, and for job quality. Questions to ask? -Time frame? -How long without water? - How many employees on site? -How many repipes have you done? -Previous client testimonials? -Type of pipe?/Brand?/Warranty info? -All patching/repairs included? -What size of pipe main? -Should i upgrade/move/change any of my plumbing related to water? -Water quality test/pressure? These are all off the top of my head. There are probably several more. Ask questions!, Get warranty info, and pricing in writing! Get permits/inspection!
If you have old pipe , such as galvanized, you need to repipe with copper or PEX. If you already have newer pipe you need to install a whole house water filtration system. I recommend a whole house filtration system on every house. Water municipalities do a great job of killing diseases and bacteria by injecting the water with chlorine, but they do not much else in the way of actually filtering the water to remove chemicals, turbidity, VOCs, or the chlorine that they put in the water. Get a water report from your water district. They are required to supply them and most can be found online. Frankly, i think the government standards set back in the 70's are way too low for water quality and i will never drink water from a tap unless it is filtered.
Possible causes could include a blockage in the hot water system, a faulty hot water valve or fixture, or sediment buildup in the hot water heater. It's also possible that there may be an issue with the hot water supply line or a malfunctioning hot water pump.