0
What else can I help you with?
In a circuit the voltage across all resistores is the same?
It depends upon the connection of the resistors, if the resistors are connected in parallel then the voltage is same where as in case of resistors connected in series the voltage is different across different resistors.
When a load is connected to the output voltage divider the output voltage will what?
When a load is connected to the output of a voltage divider, the output voltage will typically decrease due to the loading effect. This occurs because the load draws current, which can change the voltage across the resistors in the divider. The extent of the voltage drop depends on the resistance of the load relative to the resistors in the voltage divider. If the load resistance is significantly lower than the divider resistances, the output voltage will drop more noticeably.
What is the PD across two resistors connected parallel to a battery of emf 6V?
The potential difference across two resistors connected in parallel to a battery with a potential difference of 6 volts is 6 volts. Kirchoff's Voltage Law: The signed sum of the voltage drops in a series circuit is zero. This means that that the two series circuits involving the battery and each resistor have the same voltage across each other, and the series circuit involving the two resistors have the same voltage across each other.
What are voltage dividers?
Voltage dividers are used in a linear circuit to separate the input voltage into a small portion known as the output voltage. It is commonly used to get a low voltage signal equal to the voltage being measured.
What happens to the voltage values of other resistors when a short occurs in one of them?
If a short occurs in a resistor in series with other resistors, the voltage drops across the other resistors will increase. If a short occurs in a resistor in parallel with other resistors, the voltage drops across the other resistors will decrease, to zero.
In a circuit the voltage across all resistores is the same?
It depends upon the connection of the resistors, if the resistors are connected in parallel then the voltage is same where as in case of resistors connected in series the voltage is different across different resistors.
Two resistors are connected in parallel to a battery What must the votlage across these two resistors?
Both resistors will have the voltage of the battery.
What is the total voltage in a series circuit when multiple resistors are connected in series?
In a series circuit with multiple resistors connected in series, the total voltage is equal to the sum of the individual voltages across each resistor.
What are the differences between resistors connected in parallel and resistors connected in series, and how do these configurations affect the overall resistance in a circuit?
Resistors connected in parallel have the same voltage across them, while resistors connected in series have the same current passing through them. In a parallel configuration, the total resistance decreases as more resistors are added, while in a series configuration, the total resistance increases.
What happens to supply voltage if additional resistance is connected in parallel circuit?
The supply voltage in a parallel circuit remains the same regardless of the number of additional resistors connected. The voltage across each resistor in a parallel circuit is the same as the supply voltage. Adding more resistors in parallel will increase the total current drawn from the supply.
Three equal resistors connected in series across a voltage source dissipate a power of 10W what sould be the power desipated if same resistors are connected in parallel?
If three equal resistors are connected in parallel, the equivalent resistance will be one-third of the resistance in series. This lower resistance will result in a higher current flowing through the resistors when connected in parallel compared to when they are in series. Therefore, the power dissipated by the resistors in parallel will be greater than 10W.
Advantage of using connecting resistors series in terms of current and voltage?
if resistors connected in series the resistance will increase.Then it limit the flow of current through it. voltage may be increased. A: by connecting any resistors in series it will limit the current flow it will effect the current but never the voltage applied
What would be the total current and voltage dropped for each of the two resistors 7 and 9 ohms be if they're supply voltage is 230 volts?
Please specify whether the resistors are connected in series or in parallel.
Did the the total voltage across the resistors does not depend on the resistor value?
It depends on where and how the resistor is placed in a circuit. A string of series resistors will split the voltage across all them depending on their values. All of the resistors in parallel will have the same voltage across all of them no matter what their resistance is.
How does the concept of parallel resistors connected to the same voltage source affect the overall resistance in a circuit?
When resistors are connected in parallel to the same voltage source, the overall resistance in the circuit decreases. This is because the current has multiple paths to flow through, reducing the total resistance that the current encounters.
When a load is connected to the output voltage divider the output voltage will what?
When a load is connected to the output of a voltage divider, the output voltage will typically decrease due to the loading effect. This occurs because the load draws current, which can change the voltage across the resistors in the divider. The extent of the voltage drop depends on the resistance of the load relative to the resistors in the voltage divider. If the load resistance is significantly lower than the divider resistances, the output voltage will drop more noticeably.
What are Relationship between the voltage drop across the resistors and the currents through the resistors when resistors are connected in parallel?
A: The relationship is that the current will divide for each paths in a parallel circuit and the voltage drop across each will be the source voltage. In a series circuit the current will remain the same for each component but the voltage will divide to reflect each different component value. And the sum of all of the voltage drops will add to the voltage source.
